Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Audi A4 built from 2002 to 2005 (1.8T, 3.0, 2.0T, 3.2, Avant, Cabriolet).
Every 2002-2005 Audi A4 uses a 5X112 bolt pattern with a 57.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 57.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Audi A4 (B6) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| 1.8T | 2002-2005 | 15x6.5 +33 15x7 +39 16x7 +42 16x7.5 +45 17x7.5 +43 17x7.5 +45 18x8 +43 18x8 +45 |
| 3.0 | 2002-2005 | See factory sizes below |
| 2.0T | 2005 | See factory sizes below |
| 3.2 | 2005 | See factory sizes below |
| Avant | 2002-2005 | See factory sizes below |
| Cabriolet | 2003-2005 | See factory sizes below |
Wheel sizes Audi fitted to the 2002-2005 Audi A4 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 15x6.5 +33 |
| 15x7 +39 |
| 16x7 +42 |
| 16x7.5 +45 |
| 17x7.5 +43 |
| 17x7.5 +45 |
| 18x8 +43 |
| 18x8 +45 |
Widths and offsets with Verified Fitment on the 2002-2005 Audi A4: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 16-18" | 6.5" | +15 to +43 |
| 16-18" | 7" | +21 to +49 |
| 16-18" | 7.5" | +28 to +50 |
| 16-18" | 8" | +34 to +44 |
Wider still: 16x9 +26 to +37; 17x9 +26 to +37; 18x9 +26 to +37 fit with modifications (roll rear fender lips, adjustable front upper control arms for extra negative camber, hub-centric rings (57.1 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Offset range |
|---|---|---|
| 16-18" | 7" | +21 to +52 |
| 16-18" | 7.5" | +28 to +50 |
| 16-18" | 8" | +34 to +44 |
Wider still: 16x9 +26 to +37; 17x9 +26 to +37; 18x9 +26 to +37 fit with modifications (roll rear fender lips, adjustable front upper control arms for extra negative camber, hub-centric rings (57.1 mm), correct-length ball-seat lug bolts).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2002-2005 Audi A4. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.









Modifications Required (roll rear fender lips, adjustable front upper control arms for extra negative camber, hub-centric rings (57.1 mm), correct-length ball-seat lug bolts)


















Modifications Required (roll rear fender lips, adjustable front upper control arms for extra negative camber, hub-centric rings (57.1 mm), correct-length ball-seat lug bolts)









The 2002-2005 Audi A4 (B6) uses a 5X112 bolt pattern and a 57.1 mm center bore.
Factory sizes: 15x6.5 +33; 15x7 +39; 16x7 +42; 16x7.5 +45; 17x7.5 +43; 17x7.5 +45; 18x8 +43; 18x8 +45.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 16" to 18" in diameter; see the size table for the offset range at each width.