Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Audi R8 built from 2008 to 2015 (V8, V10, Spyder, V10 plus).
Every 2008-2015 Audi R8 uses a 5X112 bolt pattern with a 57.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 57.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Audi R8 (42) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| V8 | 2008-2015 | See factory sizes below |
| V10 | 2010-2015 | 19x8.5 +42 front / 19x11 +50 rear |
| Spyder | 2011-2015 | See factory sizes below |
| V10 plus | 2014-2015 | 19x8.5 +42 front / 19x11 +50 rear |
Wheel sizes Audi fitted to the 2008-2015 Audi R8 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 18x8.5 +42 front / 18x10.5 +50 rear |
| 18x10.5 +50 |
| 19x8.5 +42 front / 19x10.5 +50 rear |
| 19x8.5 +42 front / 19x11 +50 rear |
| 19x11 +50 |
Widths and offsets with Verified Fitment on the 2008-2015 Audi R8: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18-20" | 8.5" | +25 to +47 | — |
| 18-20" | 9" | +31 to +41 | — |
| 18-20" | 10.5" | — | +33 to +55 |
| 18-20" | 11" | — | +39 to +49 |
Wider still: 18x12 front — / rear +31 to +42; 19x12 front — / rear +31 to +42; 20x12 front — / rear +31 to +42 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (57.1 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 19-20" | 8.5" | +25 to +47 | — |
| 19-20" | 9" | +31 to +41 | — |
| 19-20" | 11" | — | +39 to +50 |
Wider still: 19x12 front — / rear +31 to +42; 20x12 front — / rear +31 to +42 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (57.1 mm), correct-length ball-seat lug bolts).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2008-2015 Audi R8. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.
Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (57.1 mm), correct-length ball-seat lug bolts)




Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (57.1 mm), correct-length ball-seat lug bolts)
The 2008-2015 Audi R8 (42) uses a 5X112 bolt pattern and a 57.1 mm center bore.
Factory sizes: 18x8.5 +42 front / 18x10.5 +50 rear; 18x10.5 +50; 19x8.5 +42 front / 19x10.5 +50 rear; 19x8.5 +42 front / 19x11 +50 rear; 19x11 +50.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 18" to 20" in diameter; see the size table for the offset range at each width.