Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the BMW 1 Series built from 2008 to 2013 (128i, 135i, 135is).
Every 2008-2013 BMW 1 Series uses a 5X120 bolt pattern with a 72.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 72.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the BMW 1 Series (E82/E88) and the model years each was sold. All of them share the 5X120 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| 128i | 2008-2013 | 16x7 +44 17x7 +47 17x7 +47 front / 17x7.5 +47 rear 18x7.5 +49 front / 18x8.5 +52 rear |
| 135i | 2008-2013 | 16x7 +44 17x7 +47 17x7 +47 front / 17x7.5 +47 rear 18x7.5 +49 front / 18x8.5 +52 rear |
| 135is | 2013 | 17x7 +47 17x7.5 +47 18x8.5 +52 |
Wheel sizes BMW fitted to the 2008-2013 BMW 1 Series from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 16x6.5 +33 |
| 16x7 +40 |
| 16x7 +44 |
| 17x7 +40 |
| 17x7 +47 |
| 17x7 +47 front / 17x7.5 +47 rear |
| 17x7.5 +43 |
| 17x7.5 +47 |
| 17x8 +53 |
| 18x7.5 +49 front / 18x8.5 +52 rear |
| 18x8 +52 |
| 18x8.5 +52 |
| 19x8 +52 |
Widths and offsets with Verified Fitment on the 2008-2013 BMW 1 Series: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 17-19" | 7" | +30 to +52 | +23 to +54 |
| 17-19" | 7.5" | +36 to +46 | +30 to +52 |
| 17-19" | 8" | — | +36 to +46 |
Wider still: 17x9 front — / rear +28 to +39; 18x9 front — / rear +28 to +39; 19x9 front — / rear +28 to +39 fit with modifications (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 17-19" | 7" | +30 to +52 | +23 to +57 |
| 17-19" | 7.5" | +36 to +46 | +30 to +52 |
| 17-19" | 8" | — | +36 to +46 |
Wider still: 17x9 front — / rear +28 to +39; 18x9 front — / rear +28 to +39; 19x9 front — / rear +28 to +39 fit with modifications (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2008-2013 BMW 1 Series. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.
Modifications Required (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub)












Modifications Required (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub)












The 2008-2013 BMW 1 Series (E82/E88) uses a 5X120 bolt pattern and a 72.6 mm center bore.
Factory sizes: 16x6.5 +33; 16x7 +40; 16x7 +44; 17x7 +40; 17x7 +47; 17x7 +47 front / 17x7.5 +47 rear; 17x7.5 +43; 17x7.5 +47; 17x8 +53; 18x7.5 +49 front / 18x8.5 +52 rear; 18x8 +52; 18x8.5 +52; 19x8 +52.
Bolt-on sizes run from 17" to 19" in diameter; see the size table for the offset range at each width.