Bolt pattern, center bore, factory wheel sizes and the aftermarket widths and offsets that bolt on to the BMW M5 built from 2013 to 2016.
Every 2013-2016 BMW M5 uses a 5X120 bolt pattern with a 72.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 72.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.25. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the BMW M5 (F10) and the model years each was sold. All of them share the 5X120 bolt pattern.
| Submodel | Years |
|---|---|
| Base | 2013-2016 |
Wheel sizes BMW fitted to the 2013-2016 BMW M5 from the factory. Offsets are ET in millimeters.
| Factory size |
|---|
| 19x9 +32 front / 19x9 +25 rear |
| 19x9 +32 front / 19x10 +34 rear |
| 20x9 +32 front / 20x9 +25 rear |
| 20x9 +32 front / 20x10 +34 rear |
| 20x9 +34 front / 20x10 +34 rear |
| 20x9.5 +31 front / 20x10.5 +19 rear |
Widths and offsets with Verified Fitment on the 2013-2016 BMW M5: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 19-21" | 9" | +15 to +38 | — |
| 19-21" | 9.5" | +21 to +31 | — |
| 19-21" | 10" | — | +17 to +40 |
| 19-21" | 10.5" | — | +23 to +33 |
Wider still: 19x11.5 front — / rear +15 to +26; 20x11.5 front — / rear +15 to +26; 21x11.5 front — / rear +15 to +26 fit with modifications (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2013-2016 BMW M5. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.
Modifications Required (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub)
The 2013-2016 BMW M5 (F10) uses a 5X120 bolt pattern and a 72.6 mm center bore.
Factory sizes: 19x9 +32 front / 19x9 +25 rear; 19x9 +32 front / 19x10 +34 rear; 20x9 +32 front / 20x9 +25 rear; 20x9 +32 front / 20x10 +34 rear; 20x9 +34 front / 20x10 +34 rear; 20x9.5 +31 front / 20x10.5 +19 rear.
Its wheel fasteners use a M14x1.25 thread.
Bolt-on sizes run from 19" to 21" in diameter; see the size table for the offset range at each width.