Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the BMW X7 built from 2019 to 2026 (xDrive40i, xDrive50i, M50i, M60i, ALPINA XB7).
Every 2019-2026 BMW X7 uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.25. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the BMW X7 (G07) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| xDrive40i | 2019-2026 | 20x8.5 +35 21x9.5 +36 22x9.5 +32 front / 22x10.5 +43 rear |
| xDrive50i | 2019-2022 | 20x8.5 +35 21x9.5 +36 22x10.5 +43 |
| M50i | 2020-2022 | 21x9.5 +36 22x9.5 +32 front / 22x10.5 +43 rear |
| M60i | 2023-2026 | 21x9.5 +36 |
| ALPINA XB7 | 2021-2026 | 21x9.5 +36 |
Wheel sizes BMW fitted to the 2019-2026 BMW X7 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 20x8.5 +35 |
| 21x9.5 +36 |
| 22x9.5 +32 front / 22x10.5 +43 rear |
| 22x10.5 +43 |
| 23x9.5 +32 front / 23x10.5 +43 rear |
Widths and offsets with Verified Fitment on the 2019-2026 BMW X7: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 20-23" | 8.5" | +2 to +45 | +6 to +45 |
| 24" | 8.5" | +2 to +45 | — |
| 20-23" | 9" | +8 to +48 | +12 to +48 |
| 24" | 9" | +8 to +48 | — |
| 20-23" | 9.5" | +15 to +41 | +19 to +41 |
| 24" | 9.5" | +15 to +41 | — |
| 20-23" | 10" | +21 to +35 | +25 to +35 |
| 24" | 10" | +21 to +35 | — |
| 20-24" | 10.5" | +28 to +29 | — |
Wider still: 20x11 front +13 to +28 / rear +17 to +28; 20x11.5 front +20 to +22 / rear —; 21x11 front +13 to +28 / rear +17 to +28; 21x11.5 front +20 to +22 / rear —; 22x11 front +13 to +28 / rear +17 to +28; 22x11.5 front +20 to +22 / rear —… fit with modifications (roll or trim rear fender lip / arch liner, front camber bolts for extra negative camber, hub-centric rings if wheel bore is larger than the hub).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 21-23" | 9.5" | +15 to +41 | +19 to +41 |
| 24" | 9.5" | +15 to +41 | — |
| 21-23" | 10" | +21 to +35 | +25 to +35 |
| 24" | 10" | +21 to +35 | — |
| 21-24" | 10.5" | +28 to +29 | — |
Wider still: 21x11 front +13 to +28 / rear +17 to +28; 21x11.5 front +20 to +22 / rear —; 22x11 front +13 to +28 / rear +17 to +28; 22x11.5 front +20 to +22 / rear —; 23x11 front +13 to +28 / rear +17 to +28; 23x11.5 front +20 to +22 / rear —… fit with modifications (roll or trim rear fender lip / arch liner, front camber bolts for extra negative camber, hub-centric rings if wheel bore is larger than the hub).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2019-2026 BMW X7. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.









Modifications Required (roll or trim rear fender lip / arch liner, front camber bolts for extra negative camber, hub-centric rings if wheel bore is larger than the hub)









Modifications Required (roll or trim rear fender lip / arch liner, front camber bolts for extra negative camber, hub-centric rings if wheel bore is larger than the hub)




The 2019-2026 BMW X7 (G07) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 20x8.5 +35; 21x9.5 +36; 22x9.5 +32 front / 22x10.5 +43 rear; 22x10.5 +43; 23x9.5 +32 front / 23x10.5 +43 rear.
Its wheel fasteners use a M14x1.25 thread.
Bolt-on sizes run from 20" to 24" in diameter; see the size table for the offset range at each width.