Chrysler Cirrus (JA) 1995-2000 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Chrysler Cirrus built from 1995 to 2000 (LX, LXi).

Fitment specs

Bolt pattern5X100
Center bore57.1 mm
Lug threadM12x1.5
Model years1995-2000
GenerationJA

Every 1995-2000 Chrysler Cirrus uses a 5X100 bolt pattern with a 57.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 57.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Chrysler Cirrus (JA) and the model years each was sold. All of them share the 5X100 bolt pattern.

SubmodelYearsFactory wheel sizes
LX1995-200015x6 +37
LXi1995-200015x6 +37

Factory wheel sizes

Wheel sizes Chrysler fitted to the 1995-2000 Chrysler Cirrus from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
14x6 +37
15x6 +37
16x6.5 +40
17x7 +40
17x7.5 +38
18x7.5 +35
19x8 +35

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1995-2000 Chrysler Cirrus: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

DiameterWidthOffset range
15-18"6"+2 to +47
15-18"6.5"+8 to +53
15-18"7"+14 to +50
15-18"7.5"+21 to +43
15-18"8"+27 to +37

Wider still: 15x9 +19 to +30; 16x9 +19 to +30; 17x9 +19 to +30; 18x9 +19 to +30 fit with modifications (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 1995-2000 Chrysler Cirrus. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

Modifications Required (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock)

FAQ

What is the bolt pattern of the 1995-2000 Chrysler Cirrus?

The 1995-2000 Chrysler Cirrus (JA) uses a 5X100 bolt pattern and a 57.1 mm center bore.

What size wheels came on the 1995-2000 Chrysler Cirrus from the factory?

Factory sizes: 14x6 +37; 15x6 +37; 16x6.5 +40; 17x7 +40; 17x7.5 +38; 18x7.5 +35; 19x8 +35.

What lug thread size does the 1995-2000 Chrysler Cirrus use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 1995-2000 Chrysler Cirrus without modifications?

Bolt-on sizes run from 15" to 18" in diameter; see the size table for the offset range at each width.