Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Dodge Caliber built from 2007 to 2012 (SE, SXT, Mainstreet, Heat, Uptown, R/T, SRT4).
Every 2007-2012 Dodge Caliber uses a 5X114.3 bolt pattern with a 67.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 67.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Dodge Caliber (PM) and the model years each was sold. All of them share the 5X114.3 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| SE | 2007-2012 | 15x6 +39 |
| SXT | 2007-2012 | 17x6.5 +39 |
| Mainstreet | 2010-2011 | 17x6.5 +39 |
| Heat | 2010-2011 | 18x7 +42 |
| Uptown | 2010-2011 | 17x6.5 +39 |
| R/T | 2007-2009 | 18x7 +42 |
| SRT4 | 2008-2009 | 19x7.5 +39 |
Wheel sizes Dodge fitted to the 2007-2012 Dodge Caliber from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 15x6 +39 |
| 16x6 +40 |
| 16x6.5 +40 |
| 17x6.5 +39 |
| 18x7 +42 |
| 18x7.5 +39 |
| 19x7.5 +39 |
| 20x8 +35 |
Widths and offsets with Verified Fitment on the 2007-2012 Dodge Caliber: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 15-20" | 6" | +3 to +49 |
| 15-20" | 6.5" | +9 to +55 |
| 15-20" | 7" | +15 to +51 |
| 15-20" | 7.5" | +22 to +44 |
| 15-20" | 8" | +28 to +38 |
Wider still: 15x9 +20 to +31; 16x9 +20 to +31; 17x9 +20 to +31; 18x9 +20 to +31; 19x9 +20 to +31; 20x9 +20 to +31 fit with modifications (roll front and rear fender lips, front camber bolts for -1° or more, hub-centric rings for aftermarket wheels).
| Diameter | Width | Offset range |
|---|---|---|
| 17-20" | 6.5" | +9 to +49 |
| 17-20" | 7" | +15 to +51 |
| 17-20" | 7.5" | +22 to +44 |
| 17-20" | 8" | +28 to +38 |
Wider still: 17x9 +20 to +31; 18x9 +20 to +31; 19x9 +20 to +31; 20x9 +20 to +31 fit with modifications (roll front and rear fender lips, front camber bolts for -1° or more, hub-centric rings for aftermarket wheels).
| Diameter | Width | Offset range |
|---|---|---|
| 18-20" | 7" | +15 to +51 |
| 18-20" | 7.5" | +22 to +44 |
| 18-20" | 8" | +28 to +38 |
Wider still: 18x9 +20 to +31; 19x9 +20 to +31; 20x9 +20 to +31 fit with modifications (roll front and rear fender lips, front camber bolts for -1° or more, hub-centric rings for aftermarket wheels).
| Diameter | Width | Offset range |
|---|---|---|
| 19-20" | 7.5" | +22 to +44 |
| 19-20" | 8" | +28 to +38 |
Wider still: 19x9 +20 to +31; 20x9 +20 to +31 fit with modifications (roll front and rear fender lips, front camber bolts for -1° or more, hub-centric rings for aftermarket wheels).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2007-2012 Dodge Caliber. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.







Modifications Required (roll front and rear fender lips, front camber bolts for -1° or more, hub-centric rings for aftermarket wheels)



















Modifications Required (roll front and rear fender lips, front camber bolts for -1° or more, hub-centric rings for aftermarket wheels)


















Modifications Required (roll front and rear fender lips, front camber bolts for -1° or more, hub-centric rings for aftermarket wheels)












Modifications Required (roll front and rear fender lips, front camber bolts for -1° or more, hub-centric rings for aftermarket wheels)











The 2007-2012 Dodge Caliber (PM) uses a 5X114.3 bolt pattern and a 67.1 mm center bore.
Factory sizes: 15x6 +39; 16x6 +40; 16x6.5 +40; 17x6.5 +39; 18x7 +42; 18x7.5 +39; 19x7.5 +39; 20x8 +35.
Its wheel fasteners use a M12x1.5 thread.
Bolt-on sizes run from 15" to 20" in diameter; see the size table for the offset range at each width.