Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Ford Contour built from 1995 to 2000 (GL, LX, SE, Sport, SVT).
Every 1995-2000 Ford Contour uses a 4X108 bolt pattern with a 63.4 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 63.4 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Ford Contour (CDW27) and the model years each was sold. All of them share the 4X108 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| GL | 1995-1997 | 14x5.5 +47.5 |
| LX | 1995-1999 | 14x5.5 +47.5 |
| SE | 1997-2000 | 15x6 +49.5 15x6.5 +47.5 |
| Sport | 1998-2000 | See factory sizes below |
| SVT | 1998-2000 | 16x6.5 +49.5 |
Wheel sizes Ford fitted to the 1995-2000 Ford Contour from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 14x5.5 +47.5 |
| 15x6 +49.5 |
| 15x6.5 +47.5 |
| 16x6.5 +49.5 |
Widths and offsets with Verified Fitment on the 1995-2000 Ford Contour: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 14-17" | 5.5" | +20 to +57 |
| 14-17" | 6" | +26 to +61 |
| 14-17" | 6.5" | +32 to +55 |
| 14-17" | 7" | +39 to +49 |
Wider still: 14x8 +31 to +42; 15x8 +31 to +42; 16x8 +31 to +42; 17x8 +31 to +42 fit with modifications (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock).
| Diameter | Width | Offset range |
|---|---|---|
| 15-17" | 6" | +26 to +59 |
| 15-17" | 6.5" | +32 to +55 |
| 15-17" | 7" | +39 to +49 |
Wider still: 15x8 +31 to +42; 16x8 +31 to +42; 17x8 +31 to +42 fit with modifications (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock).
| Diameter | Width | Offset range |
|---|---|---|
| 16-17" | 6.5" | +32 to +55 |
| 16-17" | 7" | +39 to +49 |
Wider still: 16x8 +31 to +42; 17x8 +31 to +42 fit with modifications (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock).
The 1995-2000 Ford Contour (CDW27) uses a 4X108 bolt pattern and a 63.4 mm center bore.
Factory sizes: 14x5.5 +47.5; 15x6 +49.5; 15x6.5 +47.5; 16x6.5 +49.5.
Its wheel fasteners use a M12x1.5 thread.
Bolt-on sizes run from 14" to 17" in diameter; see the size table for the offset range at each width.