Ford Crown Victoria (EN53) 1992-1997 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Ford Crown Victoria built from 1992 to 1997 (Base, S, LX, Touring Sedan).

Fitment specs

Bolt pattern5X114.3
Center bore70.5 mm
Lug thread1/2"-20UNF
Model years1992-1997
GenerationEN53

Every 1992-1997 Ford Crown Victoria uses a 5X114.3 bolt pattern with a 70.5 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 70.5 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is 1/2"-20UNF. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Ford Crown Victoria (EN53) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
Base1992-1997See factory sizes below
S1992-199715x6.5 +11.4
15x6.5 +8.9
LX1992-199715x6.5 +11.4
15x6.5 +8.9
16x7 +12
16x7 +6
16x7 +6.4
Touring Sedan1992See factory sizes below

Factory wheel sizes

Wheel sizes Ford fitted to the 1992-1997 Ford Crown Victoria from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
15x6.5 +8.9
15x6.5 +11.4
17x7 +12

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1992-1997 Ford Crown Victoria: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

Base, Touring Sedan

DiameterWidthOffset range
15-18"6.5"-11 to +21
15-18"7"-5 to +18
15-18"7.5"+1 to +11

Wider still: 15x8.5 -7 to +4; 16x8.5 -7 to +4; 17x8.5 -7 to +4; 18x8.5 -7 to +4 fit with modifications (roll rear fender lips, check strut / spring clearance up front (spacer may be needed), rear fender roll or pull for wide, low-offset rear wheels).

S, LX

DiameterWidthOffset range
15-18"6.5"-11 to +21
15-18"7"-5 to +18
15-18"7.5"+1 to +11

Wider still: 15x8.5 -7 to +4; 16x8.5 -7 to +4; 17x8.5 -7 to +4; 18x8.5 -7 to +4 fit with modifications (roll rear fender lips, check strut / spring clearance up front (spacer may be needed), rear fender roll or pull for wide, low-offset rear wheels).

FAQ

What is the bolt pattern of the 1992-1997 Ford Crown Victoria?

The 1992-1997 Ford Crown Victoria (EN53) uses a 5X114.3 bolt pattern and a 70.5 mm center bore.

What size wheels came on the 1992-1997 Ford Crown Victoria from the factory?

Factory sizes: 15x6.5 +8.9; 15x6.5 +11.4; 17x7 +12.

What lug thread size does the 1992-1997 Ford Crown Victoria use?

Its wheel fasteners use a 1/2"-20UNF thread.

What aftermarket wheel sizes fit the 1992-1997 Ford Crown Victoria without modifications?

Bolt-on sizes run from 15" to 18" in diameter; see the size table for the offset range at each width.