Bolt pattern, center bore, factory wheel sizes and the aftermarket widths and offsets that bolt on to the Infiniti G37 built from 2008 to 2013 (Base, Journey, x, Sport, IPL, Sedan, Convertible).
Every 2008-2013 Infiniti G37 uses a 5X114.3 bolt pattern with a 66.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.25. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Infiniti G37 (V36) and the model years each was sold. All of them share the 5X114.3 bolt pattern.
| Submodel | Years |
|---|---|
| Base | 2008-2013 |
| Journey | 2008-2013 |
| x | 2009-2013 |
| Sport | 2008-2013 |
| IPL | 2011-2013 |
| Sedan | 2009-2013 |
| Convertible | 2009-2013 |
Wheel sizes Infiniti fitted to the 2008-2013 Infiniti G37 from the factory. Offsets are ET in millimeters.
| Factory size |
|---|
| 17x7.5 +45 |
| 18x7.5 +45 |
| 18x7.5 +45 front / 18x8.5 +50 rear |
| 18x8 +43 |
| 18x8.5 +27 |
| 19x7.5 +45 front / 19x8.5 +50 rear |
| 19x8.5 +43 front / 19x9 +45 rear |
| 19x9 +30 |
| 19x9 +45 |
| 20x8 +43 front / 20x9 +45 rear |
| 20x8 +45 front / 20x9 +45 rear |
| 20x8.5 +40 front / 20x9.5 +40 rear |
| 20x9 +30 |
| 20x9 +45 |
| 20x9.5 +30 |
| 20x9.5 +40 |
Widths and offsets with Verified Fitment on the 2008-2013 Infiniti G37: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18-20" | 7.5" | -3 to +55 | — |
| 18-20" | 8" | +3 to +61 | — |
| 18-20" | 8.5" | +10 to +57 | +10 to +57 |
| 18-20" | 9" | +16 to +50 | +16 to +50 |
| 18-20" | 9.5" | +23 to +44 | +23 to +44 |
| 18-20" | 10" | +29 to +38 | +29 to +38 |
Wider still: 18x10.5 front +15 to +37 / rear +15 to +37; 18x11 front +21 to +31 / rear +21 to +31; 19x10.5 front +15 to +37 / rear +15 to +37; 19x11 front +21 to +31 / rear +21 to +31; 20x10.5 front +15 to +37 / rear +15 to +37; 20x11 front +21 to +31 / rear +21 to +31 fit with modifications (roll or pull rear fender lips, rear camber arms for -1.5° or more, front camber bolts / arms, trim inner liner if needed).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2008-2013 Infiniti G37. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.












Modifications Required (roll or pull rear fender lips, rear camber arms for -1.5° or more, front camber bolts / arms, trim inner liner if needed)
The 2008-2013 Infiniti G37 (V36) uses a 5X114.3 bolt pattern and a 66.1 mm center bore.
Factory sizes: 17x7.5 +45; 18x7.5 +45; 18x7.5 +45 front / 18x8.5 +50 rear; 18x8 +43; 18x8.5 +27; 19x7.5 +45 front / 19x8.5 +50 rear; 19x8.5 +43 front / 19x9 +45 rear; 19x9 +30; 19x9 +45; 20x8 +43 front / 20x9 +45 rear; 20x8 +45 front / 20x9 +45 rear; 20x8.5 +40 front / 20x9.5 +40 rear; 20x9 +30; 20x9 +45; 20x9.5 +30; 20x9.5 +40.
Its wheel fasteners use a M12x1.25 thread.
Bolt-on sizes run from 18" to 20" in diameter; see the size table for the offset range at each width.