Mazda MX-6 (GE) 1993-1997 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mazda MX-6 built from 1993 to 1997 (Base, LS).

Fitment specs

Bolt pattern5X114.3
Center bore67.1 mm
Lug threadM12x1.5
Model years1993-1997
GenerationGE

Every 1993-1997 Mazda MX-6 uses a 5X114.3 bolt pattern with a 67.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 67.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Mazda MX-6 (GE) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
Base1993-1997See factory sizes below
LS1993-199715x6.5 +45

Factory wheel sizes

Wheel sizes Mazda fitted to the 1993-1997 Mazda MX-6 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
14x6.5 +45
15x6.5 +45
16x6.5 +45
16x6.5 +48
17x7 +42

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1993-1997 Mazda MX-6: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

Base

DiameterWidthOffset range
14-18"6.5"+28 to +50
14-18"7"+34 to +44

Wider still: 14x8 +26 to +37; 15x8 +26 to +37; 16x8 +26 to +37; 17x8 +26 to +37; 18x8 +26 to +37 fit with modifications (roll front and rear fender lips, front camber bolts / rear camber adjustment for -1° or more, hub-centric rings if the wheel bore is larger).

LS

DiameterWidthOffset range
15-18"6.5"+28 to +50
15-18"7"+34 to +44

Wider still: 15x8 +26 to +37; 16x8 +26 to +37; 17x8 +26 to +37; 18x8 +26 to +37 fit with modifications (roll front and rear fender lips, front camber bolts / rear camber adjustment for -1° or more, hub-centric rings if the wheel bore is larger).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 1993-1997 Mazda MX-6. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

Base

Modifications Required (roll front and rear fender lips, front camber bolts / rear camber adjustment for -1° or more, hub-centric rings if the wheel bore is larger)

LS

Modifications Required (roll front and rear fender lips, front camber bolts / rear camber adjustment for -1° or more, hub-centric rings if the wheel bore is larger)

FAQ

What is the bolt pattern of the 1993-1997 Mazda MX-6?

The 1993-1997 Mazda MX-6 (GE) uses a 5X114.3 bolt pattern and a 67.1 mm center bore.

What size wheels came on the 1993-1997 Mazda MX-6 from the factory?

Factory sizes: 14x6.5 +45; 15x6.5 +45; 16x6.5 +45; 16x6.5 +48; 17x7 +42.

What lug thread size does the 1993-1997 Mazda MX-6 use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 1993-1997 Mazda MX-6 without modifications?

Bolt-on sizes run from 14" to 18" in diameter; see the size table for the offset range at each width.