Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mazda RX-8 built from 2004 to 2011 (Sport, Touring, Grand Touring, Shinka, R3).
Every 2004-2011 Mazda RX-8 uses a 5X114.3 bolt pattern with a 67.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 67.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mazda RX-8 (SE3P) and the model years each was sold. All of them share the 5X114.3 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| Sport | 2004-2011 | 18x8 +50 |
| Touring | 2004-2011 | 18x8 +50 |
| Grand Touring | 2004-2011 | 18x8 +50 |
| Shinka | 2006 | See factory sizes below |
| R3 | 2009-2011 | 19x8 +47 19x8 +45 front / 19x9 +45 rear |
Wheel sizes Mazda fitted to the 2004-2011 Mazda RX-8 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 16x7.5 +50 |
| 17x7.5 +50 |
| 18x8 +50 |
| 19x8 +47 |
| 19x8 +45 front / 19x9 +45 rear |
Widths and offsets with Verified Fitment on the 2004-2011 Mazda RX-8: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 18-20" | 8" | +24 to +55 |
| 18-20" | 8.5" | +31 to +49 |
| 18-20" | 9" | +37 to +43 |
| Diameter | Width | Offset range |
|---|---|---|
| 16-20" | 8" | +24 to +55 |
| 16-20" | 8.5" | +31 to +49 |
| 16-20" | 9" | +37 to +43 |
| Diameter | Width | Offset range |
|---|---|---|
| 19-20" | 8" | +24 to +55 |
| 19-20" | 8.5" | +31 to +49 |
| 19-20" | 9" | +37 to +43 |
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2004-2011 Mazda RX-8. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.












Modifications Required (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger)


















Modifications Required (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger)

















Modifications Required (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger)





The 2004-2011 Mazda RX-8 (SE3P) uses a 5X114.3 bolt pattern and a 67.1 mm center bore.
Factory sizes: 16x7.5 +50; 17x7.5 +50; 18x8 +50; 19x8 +47; 19x8 +45 front / 19x9 +45 rear.
Its wheel fasteners use a M12x1.5 thread.
Bolt-on sizes run from 16" to 20" in diameter; see the size table for the offset range at each width.