Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mercedes-Benz CLE-Class built from 2024 to 2026 (CLE300 4MATIC, CLE450 4MATIC, AMG CLE53).
Every 2024-2026 Mercedes-Benz CLE-Class uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz CLE-Class (C236/A236) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| CLE300 4MATIC | 2024-2026 | 18x8 +44 18x8 +44 front / 18x9 +60 rear 19x8 +45 19x8 +45 front / 19x9 +60 rear 20x8 +45 front / 20x9 +60 rear |
| CLE450 4MATIC | 2024-2026 | 19x8 +45 19x8 +45 front / 19x9 +60 rear 20x8 +45 front / 20x9 +60 rear |
| AMG CLE53 | 2024-2026 | See factory sizes below |
Wheel sizes Mercedes-Benz fitted to the 2024-2026 Mercedes-Benz CLE-Class from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 18x8 +44 |
| 18x8 +44 front / 18x9 +60 rear |
| 19x8 +45 |
| 19x8 +45 front / 19x9 +60 rear |
| 20x8 +45 front / 20x9 +60 rear |
Widths and offsets with Verified Fitment on the 2024-2026 Mercedes-Benz CLE-Class: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18-21" | 8" | +27 to +50 | +27 to +54 |
| 18-21" | 8.5" | +33 to +44 | +33 to +60 |
| 18-21" | 9" | — | +40 to +65 |
| 18-21" | 9.5" | — | +46 to +59 |
| 18-21" | 10" | — | +52 to +53 |
Wider still: 18x10.5 front — / rear +38 to +52; 18x11 front — / rear +44 to +46; 19x10.5 front — / rear +38 to +52; 19x11 front — / rear +44 to +46; 20x10.5 front — / rear +38 to +52; 20x11 front — / rear +44 to +46… fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 19-21" | 8" | +27 to +50 | — |
| 19-21" | 8.5" | +33 to +44 | — |
| 19-21" | 9" | — | +40 to +65 |
| 19-21" | 9.5" | — | +46 to +59 |
| 19-21" | 10" | — | +52 to +53 |
Wider still: 19x10.5 front — / rear +38 to +52; 19x11 front — / rear +44 to +46; 20x10.5 front — / rear +38 to +52; 20x11 front — / rear +44 to +46; 21x10.5 front — / rear +38 to +52; 21x11 front — / rear +44 to +46 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2024-2026 Mercedes-Benz CLE-Class. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.












Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)












Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)












The 2024-2026 Mercedes-Benz CLE-Class (C236/A236) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 18x8 +44; 18x8 +44 front / 18x9 +60 rear; 19x8 +45; 19x8 +45 front / 19x9 +60 rear; 20x8 +45 front / 20x9 +60 rear.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 18" to 21" in diameter; see the size table for the offset range at each width.