Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mercedes-Benz GL built from 2007 to 2012 (GL320 CDI, GL350 BlueTEC, GL450, GL550).
Every 2007-2012 Mercedes-Benz GL uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz GL (X164) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| GL320 CDI | 2007-2008 | 18x8 +53 19x8.5 +56 20x8.5 +56 21x10 +37 |
| GL350 BlueTEC | 2010-2012 | 19x8.5 +56 20x8.5 +56 21x9.5 +45 21x10 +37 |
| GL450 | 2007-2012 | 19x8.5 +56 20x8.5 +56 21x9.5 +45 21x10 +37 |
| GL550 | 2008-2012 | 21x10 +37 22x10 +37 |
Wheel sizes Mercedes-Benz fitted to the 2007-2012 Mercedes-Benz GL from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 18x8 +53 |
| 19x8.5 +56 |
| 20x8.5 +56 |
| 21x9.5 +45 |
| 21x10 +37 |
| 22x10 +37 |
Widths and offsets with Verified Fitment on the 2007-2012 Mercedes-Benz GL: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 18-21" | 8" | +32 to +63 |
| 18-21" | 8.5" | +39 to +61 |
| 18-21" | 9" | +45 to +55 |
Wider still: 18x10 +37 to +48; 19x10 +37 to +48; 20x10 +37 to +48; 21x10 +37 to +48 fit with modifications (trim front wheel-well liner / bumper cover tabs, hub-centric rings (66.6 mm), check strut and spring clearance on the inner edge, longer ball-seat lug bolts with spacers).
| Diameter | Width | Offset range |
|---|---|---|
| 19-21" | 8.5" | +39 to +61 |
| 19-21" | 9" | +45 to +55 |
Wider still: 19x10 +37 to +48; 20x10 +37 to +48; 21x10 +37 to +48 fit with modifications (trim front wheel-well liner / bumper cover tabs, hub-centric rings (66.6 mm), check strut and spring clearance on the inner edge, longer ball-seat lug bolts with spacers).
| Diameter | Width | Offset range |
|---|---|---|
| 21-22" | 10" | +37 to +42 |
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2007-2012 Mercedes-Benz GL. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.







Modifications Required (trim front wheel-well liner / bumper cover tabs, hub-centric rings (66.6 mm), check strut and spring clearance on the inner edge, longer ball-seat lug bolts with spacers)












Modifications Required (trim front wheel-well liner / bumper cover tabs, hub-centric rings (66.6 mm), check strut and spring clearance on the inner edge, longer ball-seat lug bolts with spacers)












The 2007-2012 Mercedes-Benz GL (X164) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 18x8 +53; 19x8.5 +56; 20x8.5 +56; 21x9.5 +45; 21x10 +37; 22x10 +37.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 18" to 22" in diameter; see the size table for the offset range at each width.