Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mercedes-Benz SLC-Class built from 2017 to 2020 (SLC300, AMG SLC43).
Every 2017-2020 Mercedes-Benz SLC-Class uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz SLC-Class (R172) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| SLC300 | 2017-2020 | 17x7.5 +42 17x7.5 +42 front / 17x8.5 +36 rear 17x8.5 +36 18x7.5 +42 18x7.5 +42 front / 18x8.5 +36 rear 18x8 +43 front / 18x9 +42 rear 18x8.5 +36 18x9 +42 |
| AMG SLC43 | 2017-2020 | 18x8 +42 18x8 +42 front / 18x9 +43 rear |
Wheel sizes Mercedes-Benz fitted to the 2017-2020 Mercedes-Benz SLC-Class from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 16x7 +37.5 |
| 16x7 +38 front / 16x7.5 +45.5 rear |
| 16x7 +37.5 front / 16x8 +33.5 rear |
| 16x7.5 +45.5 |
| 16x8 +33.5 |
| 17x7.5 +42 |
| 17x7.5 +42 front / 17x8.5 +36 rear |
| 17x8.5 +36 |
| 18x7.5 +42 |
| 18x7.5 +42 front / 18x8.5 +36 rear |
| 18x8 +43 front / 18x9 +42 rear |
| 18x8.5 +36 |
| 18x9 +42 |
Widths and offsets with Verified Fitment on the 2017-2020 Mercedes-Benz SLC-Class: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 17-19" | 7.5" | +6 to +52 |
| 17-19" | 8" | +12 to +48 |
| 17-19" | 8.5" | +19 to +41 |
| 17-19" | 9" | +25 to +35 |
Wider still: 17x10 +17 to +28; 18x10 +17 to +28; 19x10 +17 to +28 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Offset range |
|---|---|---|
| 18-19" | 8" | +12 to +48 |
| 18-19" | 8.5" | +19 to +41 |
| 18-19" | 9" | +25 to +35 |
Wider still: 18x10 +17 to +28; 19x10 +17 to +28 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2017-2020 Mercedes-Benz SLC-Class. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.












Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)















Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)
The 2017-2020 Mercedes-Benz SLC-Class (R172) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 16x7 +37.5; 16x7 +38 front / 16x7.5 +45.5 rear; 16x7 +37.5 front / 16x8 +33.5 rear; 16x7.5 +45.5; 16x8 +33.5; 17x7.5 +42; 17x7.5 +42 front / 17x8.5 +36 rear; 17x8.5 +36; 18x7.5 +42; 18x7.5 +42 front / 18x8.5 +36 rear; 18x8 +43 front / 18x9 +42 rear; 18x8.5 +36; 18x9 +42.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 17" to 19" in diameter; see the size table for the offset range at each width.