Mitsubishi 3000GT (Z15A/Z16A) 1991-1999 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mitsubishi 3000GT built from 1991 to 1999 (Base, SL, VR-4, Spyder SL, Spyder VR-4).

Fitment specs

Bolt pattern5X114.3
Center bore67.1 mm
Lug threadM12x1.5
Model years1991-1999
GenerationZ15A/Z16A

Every 1991-1999 Mitsubishi 3000GT uses a 5X114.3 bolt pattern with a 67.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 67.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Mitsubishi 3000GT (Z15A/Z16A) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
Base1991-1999See factory sizes below
SL1991-199916x8 +46
17x8.5 +46
VR-41991-199917x8.5 +46
18x8.5 +46
Spyder SL1995-1996See factory sizes below
Spyder VR-41995-1996See factory sizes below

Factory wheel sizes

Wheel sizes Mitsubishi fitted to the 1991-1999 Mitsubishi 3000GT from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
16x8 +46
17x8 +46
17x8.5 +46
18x8 +46
18x8.5 +46

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1991-1999 Mitsubishi 3000GT: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

Base, SL, Spyder SL, Spyder VR-4

DiameterWidthOffset range
16-19"8"+21 to +56
16-19"8.5"+28 to +50
16-19"9"+34 to +44

Wider still: 16x10 +26 to +37; 17x10 +26 to +37; 18x10 +26 to +37; 19x10 +26 to +37 fit with modifications (roll and lightly pull rear fender lips, front camber bolts / rear camber arms for -1.5° or more, check strut and caliper clearance on low-offset wheels).

VR-4

DiameterWidthOffset range
17-19"8.5"+28 to +50
17-19"9"+34 to +44

Wider still: 17x10 +26 to +37; 18x10 +26 to +37; 19x10 +26 to +37 fit with modifications (roll and lightly pull rear fender lips, front camber bolts / rear camber arms for -1.5° or more, check strut and caliper clearance on low-offset wheels).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 1991-1999 Mitsubishi 3000GT. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

Base, SL, Spyder SL, Spyder VR-4

Modifications Required (roll and lightly pull rear fender lips, front camber bolts / rear camber arms for -1.5° or more, check strut and caliper clearance on low-offset wheels)

VR-4

Modifications Required (roll and lightly pull rear fender lips, front camber bolts / rear camber arms for -1.5° or more, check strut and caliper clearance on low-offset wheels)

FAQ

What is the bolt pattern of the 1991-1999 Mitsubishi 3000GT?

The 1991-1999 Mitsubishi 3000GT (Z15A/Z16A) uses a 5X114.3 bolt pattern and a 67.1 mm center bore.

What size wheels came on the 1991-1999 Mitsubishi 3000GT from the factory?

Factory sizes: 16x8 +46; 17x8 +46; 17x8.5 +46; 18x8 +46; 18x8.5 +46.

What lug thread size does the 1991-1999 Mitsubishi 3000GT use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 1991-1999 Mitsubishi 3000GT without modifications?

Bolt-on sizes run from 16" to 19" in diameter; see the size table for the offset range at each width.