Nissan 200SX (B14) 1995-1998 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Nissan 200SX built from 1995 to 1998 (Base, SE, SE-R).

Fitment specs

Bolt pattern4X100
Center bore59.1 mm
Lug threadM12x1.25
Model years1995-1998
GenerationB14

Every 1995-1998 Nissan 200SX uses a 4X100 bolt pattern with a 59.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 59.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.25. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Nissan 200SX (B14) and the model years each was sold. All of them share the 4X100 bolt pattern.

SubmodelYearsFactory wheel sizes
Base1995-1998See factory sizes below
SE1995-199814x5.5 +40
SE-R1995-199815x6 +40

Factory wheel sizes

Wheel sizes Nissan fitted to the 1995-1998 Nissan 200SX from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
13x5 +35
14x5.5 +40
15x6 +40
16x6 +40
16x6.5 +40

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1995-1998 Nissan 200SX: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

Base

DiameterWidthOffset range
13-17"5.5"+23 to +45
13-17"6"+29 to +39

Wider still: 13x7 +21 to +32; 14x7 +21 to +32; 15x7 +21 to +32; 16x7 +21 to +32; 17x7 +21 to +32 fit with modifications (roll front and rear fender lips, front camber bolts (strut) for -1° or more, hub-centric rings if the wheel bore is larger).

SE

DiameterWidthOffset range
14-17"5.5"+23 to +45
14-17"6"+29 to +39

Wider still: 14x7 +21 to +32; 15x7 +21 to +32; 16x7 +21 to +32; 17x7 +21 to +32 fit with modifications (roll front and rear fender lips, front camber bolts (strut) for -1° or more, hub-centric rings if the wheel bore is larger).

SE-R

DiameterWidthOffset range
15-17"6"+29 to +40

Wider still: 15x7 +21 to +32; 16x7 +21 to +32; 17x7 +21 to +32 fit with modifications (roll front and rear fender lips, front camber bolts (strut) for -1° or more, hub-centric rings if the wheel bore is larger).

FAQ

What is the bolt pattern of the 1995-1998 Nissan 200SX?

The 1995-1998 Nissan 200SX (B14) uses a 4X100 bolt pattern and a 59.1 mm center bore.

What size wheels came on the 1995-1998 Nissan 200SX from the factory?

Factory sizes: 13x5 +35; 14x5.5 +40; 15x6 +40; 16x6 +40; 16x6.5 +40.

What lug thread size does the 1995-1998 Nissan 200SX use?

Its wheel fasteners use a M12x1.25 thread.

What aftermarket wheel sizes fit the 1995-1998 Nissan 200SX without modifications?

Bolt-on sizes run from 13" to 17" in diameter; see the size table for the offset range at each width.