Nissan 240SX (S13) 1989-1994 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Nissan 240SX built from 1989 to 1994 (Base, XE, SE, LE).

Fitment specs

Bolt pattern4X114.3
Center bore66.1 mm
Lug threadM12x1.25
Model years1989-1994
GenerationS13

Every 1989-1994 Nissan 240SX uses a 4X114.3 bolt pattern with a 66.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.25. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Nissan 240SX (S13) and the model years each was sold. All of them share the 4X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
Base1989-1994See factory sizes below
XE1989-199015x6 +40
SE1989-199415x6 +40
LE1991-199315x6 +40

Factory wheel sizes

Wheel sizes Nissan fitted to the 1989-1994 Nissan 240SX from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
15x6 +40

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1989-1994 Nissan 240SX: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

DiameterWidthFront offsetRear offset
15-17"6"+0 to +50-13 to +50
15-17"6.5"+6 to +53-6 to +56
15-17"7"+13 to +47+0 to +58
15-17"7.5"+19 to +41+6 to +52
15-17"8"+25 to +34+13 to +45
15-17"8.5"—+19 to +39
15-17"9"—+25 to +33

Wider still: 15x9.5 front — / rear +4 to +31; 15x10 front — / rear +10 to +25; 16x9.5 front — / rear +4 to +31; 16x10 front — / rear +10 to +25; 17x9.5 front — / rear +4 to +31; 17x10 front — / rear +10 to +25 fit with modifications (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install).

FAQ

What is the bolt pattern of the 1989-1994 Nissan 240SX?

The 1989-1994 Nissan 240SX (S13) uses a 4X114.3 bolt pattern and a 66.1 mm center bore.

What size wheels came on the 1989-1994 Nissan 240SX from the factory?

Factory sizes: 15x6 +40.

What lug thread size does the 1989-1994 Nissan 240SX use?

Its wheel fasteners use a M12x1.25 thread.

What aftermarket wheel sizes fit the 1989-1994 Nissan 240SX without modifications?

Bolt-on sizes run from 15" to 17" in diameter; see the size table for the offset range at each width.