Nissan 300ZX (Z32) 1990-1996 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Nissan 300ZX built from 1990 to 1996 (Base, 2+2, Turbo, Convertible).

Fitment specs

Bolt pattern5X114.3
Center bore66.1 mm
Lug threadM12x1.25
Model years1990-1996
GenerationZ32

Every 1990-1996 Nissan 300ZX uses a 5X114.3 bolt pattern with a 66.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.25. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Nissan 300ZX (Z32) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
Base1990-1996See factory sizes below
2+21990-1996See factory sizes below
Turbo1990-199616x7.5 +45 front / 16x8.5 +35 rear
16x8.5 +35
Convertible1993-1996See factory sizes below

Factory wheel sizes

Wheel sizes Nissan fitted to the 1990-1996 Nissan 300ZX from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
16x7.5 +45
16x7.5 +45 front / 16x8.5 +35 rear
16x8.5 +35
17x8 +40 front / 17x9 +30 rear
17x9 +30

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1990-1996 Nissan 300ZX: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

DiameterWidthFront offsetRear offset
16-17"7.5"+5 to +53—
16-17"8"+11 to +47—
16-17"8.5"+18 to +40+18 to +40
16-17"9"+24 to +34+24 to +34

Wider still: 16x10 front +16 to +27 / rear +16 to +27; 17x10 front +16 to +27 / rear +16 to +27 fit with modifications (roll or pull rear fender lips, rear camber arms for -1.5° or more, front camber bolts / arms, trim inner liner if needed).

FAQ

What is the bolt pattern of the 1990-1996 Nissan 300ZX?

The 1990-1996 Nissan 300ZX (Z32) uses a 5X114.3 bolt pattern and a 66.1 mm center bore.

What size wheels came on the 1990-1996 Nissan 300ZX from the factory?

Factory sizes: 16x7.5 +45; 16x7.5 +45 front / 16x8.5 +35 rear; 16x8.5 +35; 17x8 +40 front / 17x9 +30 rear; 17x9 +30.

What lug thread size does the 1990-1996 Nissan 300ZX use?

Its wheel fasteners use a M12x1.25 thread.

What aftermarket wheel sizes fit the 1990-1996 Nissan 300ZX without modifications?

Bolt-on sizes run from 16" to 17" in diameter; see the size table for the offset range at each width.