Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Nissan Sentra built from 2013 to 2019 (S, FE+ S, SV, SR, SL, SR Turbo, NISMO).
Every 2013-2019 Nissan Sentra uses a 5X114.3 bolt pattern with a 66.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.25. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Nissan Sentra (B17) and the model years each was sold. All of them share the 5X114.3 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| S | 2013-2019 | 16x6.5 +40 |
| FE+ S | 2013-2016 | 16x6.5 +40 |
| SV | 2013-2019 | 16x6.5 +40 |
| SR | 2014-2019 | See factory sizes below |
| SL | 2013-2019 | See factory sizes below |
| SR Turbo | 2017-2019 | See factory sizes below |
| NISMO | 2017-2019 | See factory sizes below |
Wheel sizes Nissan fitted to the 2013-2019 Nissan Sentra from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 15x6.5 +40 |
| 16x6.5 +40 |
| 16x6.5 +45 |
| 17x6.5 +45 |
| 18x7 +45 |
Widths and offsets with Verified Fitment on the 2013-2019 Nissan Sentra: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 16-19" | 6.5" | +15 to +50 |
| 16-19" | 7" | +21 to +51 |
| 16-19" | 7.5" | +28 to +44 |
| 16-19" | 8" | +34 to +38 |
| Diameter | Width | Offset range |
|---|---|---|
| 15-19" | 6.5" | +15 to +55 |
| 15-19" | 7" | +21 to +51 |
| 15-19" | 7.5" | +28 to +44 |
| 15-19" | 8" | +34 to +38 |
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2013-2019 Nissan Sentra. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.







Modifications Required (roll front and rear fender lips, front camber bolts (strut) for -1° or more, hub-centric rings if the wheel bore is larger)


















Modifications Required (roll front and rear fender lips, front camber bolts (strut) for -1° or more, hub-centric rings if the wheel bore is larger)











The 2013-2019 Nissan Sentra (B17) uses a 5X114.3 bolt pattern and a 66.1 mm center bore.
Factory sizes: 15x6.5 +40; 16x6.5 +40; 16x6.5 +45; 17x6.5 +45; 18x7 +45.
Its wheel fasteners use a M12x1.25 thread.
Bolt-on sizes run from 15" to 19" in diameter; see the size table for the offset range at each width.