Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Porsche 911 Carrera 4 built from 2013 to 2016 (Carrera 4, Carrera 4S, Targa 4, Targa 4S).
Every 2013-2016 Porsche 911 Carrera 4 uses a 5X130 bolt pattern with a 71.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 71.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Porsche 911 Carrera 4 (991) and the model years each was sold. All of them share the 5X130 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| Carrera 4 | 2013-2016 | See factory sizes below |
| Carrera 4S | 2013-2016 | 19x11 +48 20x11 +52 20x11.5 +48 |
| Targa 4 | 2014-2016 | See factory sizes below |
| Targa 4S | 2014-2016 | 19x11 +48 20x11 +52 20x11.5 +48 |
Wheel sizes Porsche fitted to the 2013-2016 Porsche 911 Carrera 4 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 19x8.5 +50 front / 19x11 +56 rear |
| 19x8.5 +54 front / 19x11 +48 rear |
| 19x11 +48 |
| 19x11 +56 |
| 20x8.5 +49 front / 20x11 +56 rear |
| 20x8.5 +49 front / 20x11.5 +56 rear |
| 20x9 +51 front / 20x11 +52 rear |
| 20x9 +51 front / 20x11.5 +48 rear |
| 20x11 +52 |
| 20x11 +56 |
| 20x11.5 +48 |
| 20x11.5 +56 |
| 20x12 +63 |
Widths and offsets with Verified Fitment on the 2013-2016 Porsche 911 Carrera 4: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 19-20" | 8.5" | +33 to +59 | — |
| 19-20" | 9" | +39 to +53 | — |
| 19-20" | 9.5" | +46 to +47 | — |
| 19-20" | 11" | — | +31 to +66 |
| 19-20" | 11.5" | — | +37 to +72 |
| 19-20" | 12" | — | +44 to +68 |
| 19-20" | 12.5" | — | +50 to +62 |
| 19-20" | 13" | — | +56 |
Wider still: 19x13.5 front — / rear +42 to +55; 19x14 front — / rear +48 to +49; 20x13.5 front — / rear +42 to +55; 20x14 front — / rear +48 to +49 fit with modifications (roll rear fender lips, rear camber/toe adjustment for extra negative camber, hub-centric rings (71.6 mm) if wheel bore is larger, longer wheel bolts when running spacers).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 19-20" | 11" | +48 | +31 to +58 |
| 19-20" | 11.5" | — | +37 to +64 |
| 19-20" | 12" | — | +44 to +68 |
| 19-20" | 12.5" | — | +50 to +62 |
| 19-20" | 13" | — | +56 |
Wider still: 19x13.5 front — / rear +42 to +55; 19x14 front — / rear +48 to +49; 20x13.5 front — / rear +42 to +55; 20x14 front — / rear +48 to +49 fit with modifications (roll rear fender lips, rear camber/toe adjustment for extra negative camber, hub-centric rings (71.6 mm) if wheel bore is larger, longer wheel bolts when running spacers).
The 2013-2016 Porsche 911 Carrera 4 (991) uses a 5X130 bolt pattern and a 71.6 mm center bore.
Factory sizes: 19x8.5 +50 front / 19x11 +56 rear; 19x8.5 +54 front / 19x11 +48 rear; 19x11 +48; 19x11 +56; 20x8.5 +49 front / 20x11 +56 rear; 20x8.5 +49 front / 20x11.5 +56 rear; 20x9 +51 front / 20x11 +52 rear; 20x9 +51 front / 20x11.5 +48 rear; 20x11 +52; 20x11 +56; 20x11.5 +48; 20x11.5 +56; 20x12 +63.
Bolt-on sizes run from 19" to 20" in diameter; see the size table for the offset range at each width.