Bolt pattern, center bore, factory wheel sizes and the aftermarket widths and offsets that bolt on to the Porsche 911 Carrera built from 2012 to 2016 (Carrera, Carrera S).
Every 2012-2016 Porsche 911 Carrera uses a 5X130 bolt pattern with a 71.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 71.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Porsche 911 Carrera (991) and the model years each was sold. All of them share the 5X130 bolt pattern.
| Submodel | Years |
|---|---|
| Carrera | 2012-2016 |
| Carrera S | 2012-2016 |
Wheel sizes Porsche fitted to the 2012-2016 Porsche 911 Carrera from the factory. Offsets are ET in millimeters.
| Factory size |
|---|
| 19x8.5 +50 front / 19x11 +77 rear |
| 19x8.5 +50 front / 19x11 +56 rear |
| 19x8.5 +54 front / 19x11 +69 rear |
| 19x8.5 +54 front / 19x11 +48 rear |
| 19x8.5 +50 front / 19x11.5 +76 rear |
| 19x11 +48 |
| 19x11 +56 |
| 19x11 +69 |
| 19x11 +77 |
| 20x8.5 +49 front / 20x11 +78 rear |
| 20x8.5 +49 front / 20x11 +56 rear |
| 20x8.5 +51 front / 20x11 +70 rear |
| 20x8.5 +49 front / 20x11.5 +56 rear |
| 20x8.5 +49 front / 20x11.5 +76 rear |
| 20x9 +51 front / 20x11 +52 rear |
| 20x9 +51 front / 20x11.5 +68 rear |
| 20x9 +51 front / 20x11.5 +48 rear |
| 20x11 +52 |
| 20x11 +56 |
| 20x11 +70 |
| 20x11 +78 |
| 20x11.5 +48 |
| 20x11.5 +56 |
| 20x11.5 +68 |
| 20x11.5 +76 |
| 20x12 +63 |
| 20x12 +70 |
Widths and offsets with Verified Fitment on the 2012-2016 Porsche 911 Carrera: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 19-20" | 8.5" | +33 to +59 | — |
| 19-20" | 9" | +39 to +53 | — |
| 19-20" | 9.5" | +46 to +47 | — |
| 19-20" | 11" | — | +31 to +75 |
| 19-20" | 11.5" | — | +37 to +75 |
| 19-20" | 12" | — | +44 to +75 |
| 19-20" | 12.5" | — | +50 to +69 |
| 19-20" | 13" | — | +56 to +62 |
Wider still: 19x13.5 front — / rear +42 to +62; 19x14 front — / rear +48 to +56; 20x13.5 front — / rear +42 to +62; 20x14 front — / rear +48 to +56 fit with modifications (roll rear fender lips, rear camber/toe adjustment for extra negative camber, hub-centric rings (71.6 mm) if wheel bore is larger, longer wheel bolts when running spacers).
The 2012-2016 Porsche 911 Carrera (991) uses a 5X130 bolt pattern and a 71.6 mm center bore.
Factory sizes: 19x8.5 +50 front / 19x11 +77 rear; 19x8.5 +50 front / 19x11 +56 rear; 19x8.5 +54 front / 19x11 +69 rear; 19x8.5 +54 front / 19x11 +48 rear; 19x8.5 +50 front / 19x11.5 +76 rear; 19x11 +48; 19x11 +56; 19x11 +69; 19x11 +77; 20x8.5 +49 front / 20x11 +78 rear; 20x8.5 +49 front / 20x11 +56 rear; 20x8.5 +51 front / 20x11 +70 rear; 20x8.5 +49 front / 20x11.5 +56 rear; 20x8.5 +49 front / 20x11.5 +76 rear; 20x9 +51 front / 20x11 +52 rear; 20x9 +51 front / 20x11.5 +68 rear; 20x9 +51 front / 20x11.5 +48 rear; 20x11 +52; 20x11 +56; 20x11 +70; 20x11 +78; 20x11.5 +48; 20x11.5 +56; 20x11.5 +68; 20x11.5 +76; 20x12 +63; 20x12 +70.
Bolt-on sizes run from 19" to 20" in diameter; see the size table for the offset range at each width.