Porsche 928 (928) 1980-1995 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Porsche 928 built from 1980 to 1995 (Base, S, S4, GT, GTS, GT).

Fitment specs

Bolt pattern5X130
Center bore71.6 mm
Lug threadM14x1.5
Model years1980-1995
Generation928

Every 1980-1995 Porsche 928 uses a 5X130 bolt pattern with a 71.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 71.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Porsche 928 (928) and the model years each was sold. All of them share the 5X130 bolt pattern.

SubmodelYearsFactory wheel sizes
Base1980-1982See factory sizes below
S1983-198616x7 +65
16x7 +65 front / 16x8 +52.3 rear
S41987-199116x7 +65
16x7 +65 front / 16x8 +52.3 rear
16x8 +60 front / 16x9 +43 rear
GT1990-199116x7 +65
16x7 +65 front / 16x8 +52.3 rear
16x8 +60 front / 16x9 +43 rear
GTS1993-199517x8 +60 front / 17x9 +43 rear
GT199216x7 +65
16x7 +65 front / 16x8 +52.3 rear
16x8 +60 front / 16x9 +43 rear

Factory wheel sizes

Wheel sizes Porsche fitted to the 1980-1995 Porsche 928 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
15x7 +65
16x7 +65
16x7 +65 front / 16x8 +52.3 rear
16x8 +52.3
16x8 +60 front / 16x9 +43 rear
16x9 +43
17x8 +60 front / 17x9 +43 rear

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1980-1995 Porsche 928: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

Base

DiameterWidthFront offsetRear offset
15-17"7"+30 to +75+22 to +70
15-17"7.5"+37 to +72+29 to +64
15-17"8"+43 to +65+35 to +58
15-17"8.5"+49 to +59+42 to +51

Wider still: 15x9.5 front +41 to +52 / rear +33 to +45; 16x9.5 front +41 to +52 / rear +33 to +45; 17x9.5 front +41 to +52 / rear +33 to +45 fit with modifications (roll rear fender lips, longer wheel studs when running spacers, camber adjustment at strut top / rear spring plate).

S, S4, GT, GT

DiameterWidthFront offsetRear offset
16-17"7"+30 to +75+22 to +70
16-17"7.5"+37 to +72+29 to +64
16-17"8"+43 to +65+35 to +58
16-17"8.5"+49 to +59+42 to +51

Wider still: 16x9.5 front +41 to +52 / rear +33 to +45; 17x9.5 front +41 to +52 / rear +33 to +45 fit with modifications (roll rear fender lips, longer wheel studs when running spacers, camber adjustment at strut top / rear spring plate).

GTS

DiameterWidthFront offsetRear offset
17"8"+43 to +65—
17"8.5"+49 to +59—
17"9"—+43 to +45

Wider still: 17x9.5 front +41 to +52 / rear +33 to +45 fit with modifications (roll rear fender lips, longer wheel studs when running spacers, camber adjustment at strut top / rear spring plate).

FAQ

What is the bolt pattern of the 1980-1995 Porsche 928?

The 1980-1995 Porsche 928 (928) uses a 5X130 bolt pattern and a 71.6 mm center bore.

What size wheels came on the 1980-1995 Porsche 928 from the factory?

Factory sizes: 15x7 +65; 16x7 +65; 16x7 +65 front / 16x8 +52.3 rear; 16x8 +52.3; 16x8 +60 front / 16x9 +43 rear; 16x9 +43; 17x8 +60 front / 17x9 +43 rear.

What lug thread size does the 1980-1995 Porsche 928 use?

Its wheel fasteners use a M14x1.5 thread.

What aftermarket wheel sizes fit the 1980-1995 Porsche 928 without modifications?

Bolt-on sizes run from 15" to 17" in diameter; see the size table for the offset range at each width.