Porsche 968 (968) 1992-1995 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Porsche 968 built from 1992 to 1995 (Coupe, Cabriolet).

Fitment specs

Bolt pattern5X130
Center bore71.6 mm
Lug threadM14x1.5
Model years1992-1995
Generation968

Every 1992-1995 Porsche 968 uses a 5X130 bolt pattern with a 71.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 71.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Porsche 968 (968) and the model years each was sold. All of them share the 5X130 bolt pattern.

SubmodelYearsFactory wheel sizes
Coupe1992-199516x7 +55 front / 16x8 +52 rear
Cabriolet1992-199516x7 +55 front / 16x8 +52 rear

Factory wheel sizes

Wheel sizes Porsche fitted to the 1992-1995 Porsche 968 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
16x7 +55 front / 16x8 +52 rear
17x7.5 +55 front / 17x9 +55 rear
18x8 +55 front / 18x9 +55 rear
18x10 +65
18x11 +63

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1992-1995 Porsche 968: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

DiameterWidthFront offsetRear offset
16-18"7"+31 to +65—
16-18"7.5"+38 to +60—
16-18"8"+44 to +54+25 to +62
16-18"8.5"—+32 to +67
16-18"9"—+38 to +60
16-18"9.5"—+44 to +54

Wider still: 16x10.5 front — / rear +36 to +47; 17x10.5 front — / rear +36 to +47; 18x10.5 front — / rear +36 to +47 fit with modifications (roll rear fender lips, longer wheel studs when running spacers, camber adjustment at strut top / rear spring plate).

FAQ

What is the bolt pattern of the 1992-1995 Porsche 968?

The 1992-1995 Porsche 968 (968) uses a 5X130 bolt pattern and a 71.6 mm center bore.

What size wheels came on the 1992-1995 Porsche 968 from the factory?

Factory sizes: 16x7 +55 front / 16x8 +52 rear; 17x7.5 +55 front / 17x9 +55 rear; 18x8 +55 front / 18x9 +55 rear; 18x10 +65; 18x11 +63.

What lug thread size does the 1992-1995 Porsche 968 use?

Its wheel fasteners use a M14x1.5 thread.

What aftermarket wheel sizes fit the 1992-1995 Porsche 968 without modifications?

Bolt-on sizes run from 16" to 18" in diameter; see the size table for the offset range at each width.