Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Porsche Boxster built from 1997 to 2004 (Base, S, S 550 Spyder Anniversary).
Every 1997-2004 Porsche Boxster uses a 5X130 bolt pattern with a 71.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 71.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Porsche Boxster (986) and the model years each was sold. All of them share the 5X130 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| Base | 1997-2004 | See factory sizes below |
| S | 2000-2004 | 17x7 +55 front / 17x8.5 +50 rear 17x7.5 +50 front / 17x8.5 +50 rear |
| S 550 Spyder Anniversary | 2004 | See factory sizes below |
Wheel sizes Porsche fitted to the 1997-2004 Porsche Boxster from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 16x6 +50 front / 16x7 +40 rear |
| 17x7 +55 front / 17x8.5 +50 rear |
| 17x7.5 +50 front / 17x8.5 +50 rear |
| 17x8.5 +50 |
| 18x7.5 +50 front / 18x9 +52 rear |
| 18x7.5 +52 front / 18x9 +52 rear |
| 18x8 +50 front / 18x9 +52 rear |
| 18x8 +45 front / 18x10 +45 rear |
| 18x9 +52 |
| 18x10 +45 |
Widths and offsets with Verified Fitment on the 1997-2004 Porsche Boxster: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 16-18" | 6" | +25 to +60 | — |
| 16-18" | 6.5" | +32 to +66 | — |
| 16-18" | 7" | +38 to +60 | +14 to +50 |
| 16-18" | 7.5" | +44 to +54 | +20 to +56 |
| 16-18" | 8" | — | +26 to +62 |
| 16-18" | 8.5" | — | +33 to +55 |
| 16-18" | 9" | — | +39 to +49 |
Wider still: 16x10 front — / rear +31 to +42; 17x10 front — / rear +31 to +42; 18x10 front — / rear +31 to +42 fit with modifications (roll rear fender lips, rear camber/toe adjustment for extra negative camber, hub-centric rings (71.6 mm) if wheel bore is larger, longer wheel bolts when running spacers).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 17-18" | 7" | +38 to +60 | — |
| 17-18" | 7.5" | +44 to +54 | — |
| 17-18" | 8.5" | — | +33 to +55 |
| 17-18" | 9" | — | +39 to +49 |
Wider still: 17x10 front — / rear +31 to +42; 18x10 front — / rear +31 to +42 fit with modifications (roll rear fender lips, rear camber/toe adjustment for extra negative camber, hub-centric rings (71.6 mm) if wheel bore is larger, longer wheel bolts when running spacers).
The 1997-2004 Porsche Boxster (986) uses a 5X130 bolt pattern and a 71.6 mm center bore.
Factory sizes: 16x6 +50 front / 16x7 +40 rear; 17x7 +55 front / 17x8.5 +50 rear; 17x7.5 +50 front / 17x8.5 +50 rear; 17x8.5 +50; 18x7.5 +50 front / 18x9 +52 rear; 18x7.5 +52 front / 18x9 +52 rear; 18x8 +50 front / 18x9 +52 rear; 18x8 +45 front / 18x10 +45 rear; 18x9 +52; 18x10 +45.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 16" to 18" in diameter; see the size table for the offset range at each width.