Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Toyota 86 built from 2017 to 2020 (Base, GT, GT Black, TRD Special Edition, Hakone Edition).
Every 2017-2020 Toyota 86 uses a 5X100 bolt pattern with a 56.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 56.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.25. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Toyota 86 (ZN6) and the model years each was sold. All of them share the 5X100 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| Base | 2017-2020 | See factory sizes below |
| GT | 2018-2020 | 17x7 +48 18x7.5 +48 18x7.5 +45 front / 18x8 +45 rear |
| GT Black | 2018 | 17x7 +48 |
| TRD Special Edition | 2019 | 18x7.5 +48 18x7.5 +45 front / 18x8 +45 rear |
| Hakone Edition | 2020 | 17x7 +48 |
Wheel sizes Toyota fitted to the 2017-2020 Toyota 86 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 17x7 +48 |
| 18x7.5 +48 |
| 18x7.5 +45 front / 18x8 +45 rear |
| 18x7.5 +45 front / 18x8.5 +45 rear |
Widths and offsets with Verified Fitment on the 2017-2020 Toyota 86: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18-19" | 7.5" | +28 to +55 | — |
| 18-19" | 8" | +34 to +51 | +28 to +51 |
| 18-19" | 8.5" | +41 to +44 | +34 to +44 |
Wider still: 18x9.5 front — / rear +26 to +37; 19x9.5 front — / rear +26 to +37 fit with modifications (roll front and rear fender lips, front camber bolts for extra negative camber, hub-centric rings for aftermarket wheels).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18-19" | 7" | +21 to +58 | +15 to +58 |
| 18-19" | 7.5" | +28 to +57 | +22 to +57 |
| 18-19" | 8" | +34 to +51 | +28 to +51 |
| 18-19" | 8.5" | +41 to +44 | +34 to +44 |
Wider still: 18x9.5 front — / rear +26 to +37; 19x9.5 front — / rear +26 to +37 fit with modifications (roll front and rear fender lips, front camber bolts for extra negative camber, hub-centric rings for aftermarket wheels).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18-19" | 7.5" | +28 to +57 | +22 to +57 |
| 18-19" | 8" | +34 to +51 | +28 to +51 |
| 18-19" | 8.5" | +41 to +44 | +34 to +44 |
Wider still: 18x9.5 front — / rear +26 to +37; 19x9.5 front — / rear +26 to +37 fit with modifications (roll front and rear fender lips, front camber bolts for extra negative camber, hub-centric rings for aftermarket wheels).
The 2017-2020 Toyota 86 (ZN6) uses a 5X100 bolt pattern and a 56.1 mm center bore.
Factory sizes: 17x7 +48; 18x7.5 +48; 18x7.5 +45 front / 18x8 +45 rear; 18x7.5 +45 front / 18x8.5 +45 rear.
Its wheel fasteners use a M12x1.25 thread.
Bolt-on sizes run from 18" to 19" in diameter; see the size table for the offset range at each width.