Toyota C-HR (AX10) 2018-2022 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Toyota C-HR built from 2018 to 2022 (LE, XLE, XLE Premium, Limited, Nightshade).

Fitment specs

Bolt pattern5X114.3
Center bore60.1 mm
Lug threadM12x1.5
Model years2018-2022
GenerationAX10

Every 2018-2022 Toyota C-HR uses a 5X114.3 bolt pattern with a 60.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 60.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Toyota C-HR (AX10) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
LE2019-202217x6.5 +45
XLE2018-202218x7 +50
XLE Premium201818x7 +50
Limited2019-202218x7 +50
Nightshade2021-2022See factory sizes below

Factory wheel sizes

Wheel sizes Toyota fitted to the 2018-2022 Toyota C-HR from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
17x6.5 +45
18x7 +50

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 2018-2022 Toyota C-HR: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

LE, Nightshade

DiameterWidthOffset range
17-19"6.5"+28 to +55
17-19"7"+34 to +56
17-19"7.5"+41 to +49

Wider still: 17x8 +26 to +43; 17x8.5 +33 to +37; 18x8 +26 to +43; 18x8.5 +33 to +37; 19x8 +26 to +43; 19x8.5 +33 to +37 fit with modifications (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels).

XLE, XLE Premium, Limited

DiameterWidthOffset range
18-19"7"+34 to +56
18-19"7.5"+41 to +49

Wider still: 18x8 +26 to +43; 18x8.5 +33 to +37; 19x8 +26 to +43; 19x8.5 +33 to +37 fit with modifications (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 2018-2022 Toyota C-HR. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

LE, Nightshade

Modifications Required (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels)

XLE, XLE Premium, Limited

Modifications Required (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels)

FAQ

What is the bolt pattern of the 2018-2022 Toyota C-HR?

The 2018-2022 Toyota C-HR (AX10) uses a 5X114.3 bolt pattern and a 60.1 mm center bore.

What size wheels came on the 2018-2022 Toyota C-HR from the factory?

Factory sizes: 17x6.5 +45; 18x7 +50.

What lug thread size does the 2018-2022 Toyota C-HR use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 2018-2022 Toyota C-HR without modifications?

Bolt-on sizes run from 17" to 19" in diameter; see the size table for the offset range at each width.