Toyota Crown Signia 1st Gen 2025-2026 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Toyota Crown Signia built from 2025 to 2026 (XLE, Limited).

Fitment specs

Bolt pattern5X114.3
Center bore60.1 mm
Lug threadM14x1.5
Model years2025-2026
Generation1st Gen

Every 2025-2026 Toyota Crown Signia uses a 5X114.3 bolt pattern with a 60.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 60.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Toyota Crown Signia (1st Gen) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
XLE2025-202619x7 +40
Limited2025-202621x8.5 +35

Factory wheel sizes

Wheel sizes Toyota fitted to the 2025-2026 Toyota Crown Signia from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
19x7 +40
21x8.5 +35

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 2025-2026 Toyota Crown Signia: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

XLE

DiameterWidthOffset range
19-23"7"-1 to +50
19-23"7.5"+5 to +53
19-23"8"+11 to +47
19-23"8.5"+18 to +40
19-23"9"+24 to +34

Wider still: 19x10 +16 to +27; 20x10 +16 to +27; 21x10 +16 to +27; 22x10 +16 to +27; 23x10 +16 to +27 fit with modifications (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels).

Limited

DiameterWidthOffset range
21-23"8.5"+18 to +40
21-23"9"+24 to +34

Wider still: 21x10 +16 to +27; 22x10 +16 to +27; 23x10 +16 to +27 fit with modifications (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 2025-2026 Toyota Crown Signia. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

Modifications Required (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels)

FAQ

What is the bolt pattern of the 2025-2026 Toyota Crown Signia?

The 2025-2026 Toyota Crown Signia (1st Gen) uses a 5X114.3 bolt pattern and a 60.1 mm center bore.

What size wheels came on the 2025-2026 Toyota Crown Signia from the factory?

Factory sizes: 19x7 +40; 21x8.5 +35.

What lug thread size does the 2025-2026 Toyota Crown Signia use?

Its wheel fasteners use a M14x1.5 thread.

What aftermarket wheel sizes fit the 2025-2026 Toyota Crown Signia without modifications?

Bolt-on sizes run from 19" to 23" in diameter; see the size table for the offset range at each width.