Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Toyota Grand Highlander built from 2024 to 2026 (XLE, Limited, Platinum, Hybrid XLE, Hybrid Limited, Hybrid MAX Limited, Hybrid MAX Platinum).
Every 2024-2026 Toyota Grand Highlander uses a 5X120 bolt pattern with a 60.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 60.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Toyota Grand Highlander (AS10) and the model years each was sold. All of them share the 5X120 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| XLE | 2024-2026 | 18x7.5 +35 |
| Limited | 2024-2026 | 20x8 +40 |
| Platinum | 2024-2026 | 20x8 +40 |
| Hybrid XLE | 2024-2026 | 18x7.5 +35 |
| Hybrid Limited | 2024-2026 | 20x8 +40 |
| Hybrid MAX Limited | 2024-2026 | 20x8 +40 |
| Hybrid MAX Platinum | 2024-2026 | 20x8 +40 |
Wheel sizes Toyota fitted to the 2024-2026 Toyota Grand Highlander from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 18x7.5 +35 |
| 20x8 +40 |
Widths and offsets with Verified Fitment on the 2024-2026 Toyota Grand Highlander: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 18-22" | 7.5" | +16 to +45 |
| 18-22" | 8" | +23 to +45 |
| 18-22" | 8.5" | +29 to +39 |
Wider still: 18x9.5 +21 to +32; 19x9.5 +21 to +32; 20x9.5 +21 to +32; 21x9.5 +21 to +32; 22x9.5 +21 to +32 fit with modifications (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels).
| Diameter | Width | Offset range |
|---|---|---|
| 20-22" | 8" | +23 to +45 |
| 20-22" | 8.5" | +29 to +39 |
Wider still: 20x9.5 +21 to +32; 21x9.5 +21 to +32; 22x9.5 +21 to +32 fit with modifications (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2024-2026 Toyota Grand Highlander. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.










Modifications Required (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels)





Modifications Required (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels)
The 2024-2026 Toyota Grand Highlander (AS10) uses a 5X120 bolt pattern and a 60.1 mm center bore.
Factory sizes: 18x7.5 +35; 20x8 +40.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 18" to 22" in diameter; see the size table for the offset range at each width.