Toyota MR2 (W20) 1991-1995 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Toyota MR2 built from 1991 to 1995 (Base, Turbo).

Fitment specs

Bolt pattern5X114.3
Center bore60.1 mm
Lug threadM12x1.5
Model years1991-1995
GenerationW20

Every 1991-1995 Toyota MR2 uses a 5X114.3 bolt pattern with a 60.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 60.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Toyota MR2 (W20) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
Base1991-1995See factory sizes below
Turbo1993-199515x6 +45 front / 15x7 +45 rear

Factory wheel sizes

Wheel sizes Toyota fitted to the 1991-1995 Toyota MR2 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
14x6 +45 front / 14x7 +45 rear
15x6 +45 front / 15x7 +45 rear

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1991-1995 Toyota MR2: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

Base

DiameterWidthFront offsetRear offset
14-17"6"+15 to +55—
14-17"6.5"+21 to +51—
14-17"7"+28 to +44+15 to +55
14-17"7.5"+34 to +38+21 to +51
14-17"8"—+28 to +44
14-17"8.5"—+34 to +38

Turbo

DiameterWidthFront offsetRear offset
15-17"6"+15 to +55—
15-17"6.5"+21 to +51—
15-17"7"+28 to +44+15 to +55
15-17"7.5"+34 to +38+21 to +51
15-17"8"—+28 to +44
15-17"8.5"—+34 to +38

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 1991-1995 Toyota MR2. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

Base

Turbo

FAQ

What is the bolt pattern of the 1991-1995 Toyota MR2?

The 1991-1995 Toyota MR2 (W20) uses a 5X114.3 bolt pattern and a 60.1 mm center bore.

What size wheels came on the 1991-1995 Toyota MR2 from the factory?

Factory sizes: 14x6 +45 front / 14x7 +45 rear; 15x6 +45 front / 15x7 +45 rear.

What lug thread size does the 1991-1995 Toyota MR2 use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 1991-1995 Toyota MR2 without modifications?

Bolt-on sizes run from 14" to 17" in diameter; see the size table for the offset range at each width.