Audi 90 (B3) 1988-1991 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Audi 90 built from 1988 to 1991 (Base, Quattro, Quattro 20V).

Fitment specs

Bolt pattern4X108
Center bore57.1 mm
Lug threadM14x1.5
Model years1988-1991
GenerationB3

Every 1988-1991 Audi 90 uses a 4X108 bolt pattern with a 57.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 57.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Audi 90 (B3) and the model years each was sold. All of them share the 4X108 bolt pattern.

SubmodelYearsFactory wheel sizes
Base1988-1991See factory sizes below
Quattro1988-199114x6 +45
Quattro 20V1990-199115x6 +42
15x7 +45

Factory wheel sizes

Wheel sizes Audi fitted to the 1988-1991 Audi 90 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
14x5.5 +45
14x6 +45
15x6 +42
15x7 +45
16x7 +38

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1988-1991 Audi 90: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

Base, Quattro

DiameterWidthOffset range
14-17"6"+28 to +51
14-17"6.5"+34 to +44

Wider still: 14x7.5 +26 to +37; 15x7.5 +26 to +37; 16x7.5 +26 to +37; 17x7.5 +26 to +37 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (57.1 mm), correct-length ball-seat lug bolts).

Quattro 20V

DiameterWidthOffset range
15-17"6"+28 to +51
15-17"6.5"+34 to +44

Wider still: 15x7.5 +26 to +37; 16x7.5 +26 to +37; 17x7.5 +26 to +37 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (57.1 mm), correct-length ball-seat lug bolts).

FAQ

What is the bolt pattern of the 1988-1991 Audi 90?

The 1988-1991 Audi 90 (B3) uses a 4X108 bolt pattern and a 57.1 mm center bore.

What size wheels came on the 1988-1991 Audi 90 from the factory?

Factory sizes: 14x5.5 +45; 14x6 +45; 15x6 +42; 15x7 +45; 16x7 +38.

What lug thread size does the 1988-1991 Audi 90 use?

Its wheel fasteners use a M14x1.5 thread.

What aftermarket wheel sizes fit the 1988-1991 Audi 90 without modifications?

Bolt-on sizes run from 14" to 17" in diameter; see the size table for the offset range at each width.