Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the BMW 8 Series built from 1991 to 1997 (840Ci, 850i, 850Ci, 850CSi).
Every 1991-1997 BMW 8 Series uses a 5X120 bolt pattern with a 72.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 72.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the BMW 8 Series (E31) and the model years each was sold. All of them share the 5X120 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| 840Ci | 1994-1997 | 16x7.5 +15 17x8 +10 front / 17x9 +19 rear |
| 850i | 1991-1993 | 16x7.5 +15 17x8 +10 front / 17x9 +19 rear |
| 850Ci | 1994-1997 | 16x7.5 +15 17x8 +10 front / 17x9 +19 rear |
| 850CSi | 1994-1995 | 17x8 +10 front / 17x9 +19 rear 18x8 +13 front / 18x9.5 +25 rear |
Wheel sizes BMW fitted to the 1991-1997 BMW 8 Series from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 16x7.5 +15 |
| 17x8 +10 front / 17x9 +19 rear |
| 17x9 +19 |
| 18x8 +13 front / 18x9.5 +25 rear |
Widths and offsets with Verified Fitment on the 1991-1997 BMW 8 Series: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 16-18" | 7.5" | -13 to +22 | -17 to +25 |
| 16-18" | 8" | -7 to +15 | -11 to +31 |
| 16-18" | 8.5" | -1 to +9 | -4 to +31 |
| 16-18" | 9" | — | +2 to +24 |
| 16-18" | 9.5" | — | +8 to +18 |
Wider still: 16x10.5 front — / rear +0 to +11; 17x10.5 front — / rear +0 to +11; 18x10.5 front — / rear +0 to +11 fit with modifications (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 17-18" | 8" | -7 to +15 | — |
| 17-18" | 8.5" | -1 to +9 | — |
| 17-18" | 9" | — | +2 to +24 |
| 17-18" | 9.5" | — | +8 to +18 |
Wider still: 17x10.5 front — / rear +0 to +11; 18x10.5 front — / rear +0 to +11 fit with modifications (roll rear fender lips, adjustable rear camber arms for -1.5° or more, front camber plates, hub-centric rings if wheel bore is larger than the hub).
The 1991-1997 BMW 8 Series (E31) uses a 5X120 bolt pattern and a 72.6 mm center bore.
Factory sizes: 16x7.5 +15; 17x8 +10 front / 17x9 +19 rear; 17x9 +19; 18x8 +13 front / 18x9.5 +25 rear.
Its wheel fasteners use a M12x1.5 thread.
Bolt-on sizes run from 16" to 18" in diameter; see the size table for the offset range at each width.