Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Dodge Challenger built from 2008 to 2010 (SE, R/T, SRT8).
Every 2008-2010 Dodge Challenger uses a 5X115 bolt pattern with a 71.5 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 71.5 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Dodge Challenger (LC) and the model years each was sold. All of them share the 5X115 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| SE | 2009-2010 | 17x7 +22 |
| R/T | 2009-2010 | 18x7.5 +24 |
| SRT8 | 2008-2010 | 20x8 +24 20x9 +25.5 |
Wheel sizes Dodge fitted to the 2008-2010 Dodge Challenger from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 17x7 +22 |
| 18x7.5 +24 |
| 19x7.5 +24 |
| 20x8 +24 |
| 20x9 +25.5 |
| 21x8.5 +25 |
| 22x9 +20 |
Widths and offsets with Verified Fitment on the 2008-2010 Dodge Challenger: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 17-20" | 7" | -11 to +32 | -19 to +32 |
| 17-20" | 7.5" | -5 to +37 | -13 to +38 |
| 17-20" | 8" | +1 to +31 | -6 to +38 |
| 17-20" | 8.5" | +8 to +24 | +0 to +32 |
| 17-20" | 9" | +14 to +18 | +6 to +25 |
| 17-20" | 9.5" | — | +13 to +19 |
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 18-20" | 7.5" | -5 to +34 | -13 to +34 |
| 18-20" | 8" | +1 to +31 | -6 to +38 |
| 18-20" | 8.5" | +8 to +24 | +0 to +32 |
| 18-20" | 9" | +14 to +18 | +6 to +25 |
| 18-20" | 9.5" | — | +13 to +19 |
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 20" | 8" | +1 to +31 | -6 to +34 |
| 20" | 8.5" | +8 to +24 | +0 to +32 |
| 20" | 9" | +14 to +18 | +6 to +25 |
| 20" | 9.5" | — | +13 to +19 |
The 2008-2010 Dodge Challenger (LC) uses a 5X115 bolt pattern and a 71.5 mm center bore.
Factory sizes: 17x7 +22; 18x7.5 +24; 19x7.5 +24; 20x8 +24; 20x9 +25.5; 21x8.5 +25; 22x9 +20.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 17" to 20" in diameter; see the size table for the offset range at each width.