Ford Bronco 4th Gen 1987-1991 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Ford Bronco built from 1987 to 1991 (Custom, XLT, Eddie Bauer, Nite, Silver Anniversary).

Fitment specs

Bolt pattern5X139.7
Center bore87.1 mm
Lug thread1/2"-20UNF
Model years1987-1991
Generation4th Gen

Every 1987-1991 Ford Bronco uses a 5X139.7 bolt pattern with a 87.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 87.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is 1/2"-20UNF. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Ford Bronco (4th Gen) and the model years each was sold. All of them share the 5X139.7 bolt pattern.

SubmodelYearsFactory wheel sizes
Custom1987-199015x6 +0
15x7 +10
XLT1987-199115x6 +0
15x7 +10
Eddie Bauer1987-199115x6 +0
15x7 +10
Nite1991See factory sizes below
Silver Anniversary1991See factory sizes below

Factory wheel sizes

Wheel sizes Ford fitted to the 1987-1991 Ford Bronco from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
15x6 +0
15x7 +10

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1987-1991 Ford Bronco: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

Custom, XLT, Eddie Bauer

DiameterWidthOffset range
15-20"6"-17 to +5
15-20"6.5"-11 to -1

Wider still: 15x7.5 -19 to -8; 16x7.5 -19 to -8; 17x7.5 -19 to -8; 18x7.5 -19 to -8; 19x7.5 -19 to -8; 20x7.5 -19 to -8 fit with modifications (leveling kit or small lift for larger tires, trim front fender liner and air dam, check upper control arm / sway bar clearance).

Nite, Silver Anniversary

DiameterWidthOffset range
15-20"6"-17 to +5
15-20"6.5"-11 to -1

Wider still: 15x7.5 -19 to -8; 16x7.5 -19 to -8; 17x7.5 -19 to -8; 18x7.5 -19 to -8; 19x7.5 -19 to -8; 20x7.5 -19 to -8 fit with modifications (leveling kit or small lift for larger tires, trim front fender liner and air dam, check upper control arm / sway bar clearance).

FAQ

What is the bolt pattern of the 1987-1991 Ford Bronco?

The 1987-1991 Ford Bronco (4th Gen) uses a 5X139.7 bolt pattern and a 87.1 mm center bore.

What size wheels came on the 1987-1991 Ford Bronco from the factory?

Factory sizes: 15x6 +0; 15x7 +10.

What lug thread size does the 1987-1991 Ford Bronco use?

Its wheel fasteners use a 1/2"-20UNF thread.

What aftermarket wheel sizes fit the 1987-1991 Ford Bronco without modifications?

Bolt-on sizes run from 15" to 20" in diameter; see the size table for the offset range at each width.