Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Ford Taurus built from 2010 to 2019 (SE, SEL, Limited, SHO, Police Interceptor).
Every 2010-2019 Ford Taurus uses a 5X114.3 bolt pattern with a 63.4 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 63.4 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is 1/2"-20UNF. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Ford Taurus (6th Gen (D258)) and the model years each was sold. All of them share the 5X114.3 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| SE | 2010-2019 | 17x7.5 +39 18x7.5 +39 18x8 +39 |
| SEL | 2010-2019 | 18x7.5 +39 18x8 +39 |
| Limited | 2010-2019 | 19x8 +44 19x8.5 +39 |
| SHO | 2010-2019 | 19x8 +44 19x8.5 +39 20x8 +39 |
| Police Interceptor | 2013-2019 | 18x8 +39 |
Wheel sizes Ford fitted to the 2010-2019 Ford Taurus from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 17x7.5 +39 |
| 18x7.5 +39 |
| 18x8 +39 |
| 19x8 +44 |
| 19x8.5 +39 |
| 20x8 +39 |
Widths and offsets with Verified Fitment on the 2010-2019 Ford Taurus: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 17-20" | 7.5" | +18 to +49 |
| 17-20" | 8" | +25 to +49 |
| 17-20" | 8.5" | +31 to +43 |
| 17-20" | 9" | +37 |
Wider still: 17x9.5 +27 to +30; 18x9.5 +27 to +30; 19x9.5 +27 to +30; 20x9.5 +27 to +30 fit with modifications (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock).
| Diameter | Width | Offset range |
|---|---|---|
| 18-20" | 7.5" | +18 to +49 |
| 18-20" | 8" | +25 to +49 |
| 18-20" | 8.5" | +31 to +43 |
| 18-20" | 9" | +37 |
Wider still: 18x9.5 +27 to +30; 19x9.5 +27 to +30; 20x9.5 +27 to +30 fit with modifications (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock).
| Diameter | Width | Offset range |
|---|---|---|
| 19-20" | 8" | +25 to +49 |
| 19-20" | 8.5" | +31 to +43 |
| 19-20" | 9" | +37 |
Wider still: 19x9.5 +27 to +30; 20x9.5 +27 to +30 fit with modifications (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock).
| Diameter | Width | Offset range |
|---|---|---|
| 18-20" | 8" | +25 to +49 |
| 18-20" | 8.5" | +31 to +43 |
| 18-20" | 9" | +37 |
Wider still: 18x9.5 +27 to +30; 19x9.5 +27 to +30; 20x9.5 +27 to +30 fit with modifications (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2010-2019 Ford Taurus. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.












Modifications Required (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock)














Modifications Required (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock)













Modifications Required (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock)












Modifications Required (roll front and rear fender lips, front camber bolts for added negative camber, trim front fender liner if it rubs at full lock)
The 2010-2019 Ford Taurus (6th Gen (D258)) uses a 5X114.3 bolt pattern and a 63.4 mm center bore.
Factory sizes: 17x7.5 +39; 18x7.5 +39; 18x8 +39; 19x8 +44; 19x8.5 +39; 20x8 +39.
Its wheel fasteners use a 1/2"-20UNF thread.
Bolt-on sizes run from 17" to 20" in diameter; see the size table for the offset range at each width.