Honda S2000 (AP1) 2000-2003 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes and the aftermarket widths and offsets that bolt on to the Honda S2000 built from 2000 to 2003.

Fitment specs

Bolt pattern5X114.3
Center bore64.1 mm
Lug threadM12x1.5
Model years2000-2003
GenerationAP1

Every 2000-2003 Honda S2000 uses a 5X114.3 bolt pattern with a 64.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 64.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Honda S2000 (AP1) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYears
Base2000-2003

Factory wheel sizes

Wheel sizes Honda fitted to the 2000-2003 Honda S2000 from the factory. Offsets are ET in millimeters.

Factory size
16x6.5 +55 front / 16x7.5 +65 rear
17x7 +55 front / 17x8.5 +65 rear

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 2000-2003 Honda S2000: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

DiameterWidthFront offsetRear offset
16-17"6.5"+26 to +65—
16-17"7"+33 to +70—
16-17"7.5"+39 to +64+26 to +75
16-17"8"+45 to +58+33 to +69
16-17"8.5"—+39 to +62
16-17"9"—+45 to +56

Wider still: 16x9.5 front +37 to +59 / rear +37 to +59; 16x10 front +43 to +53 / rear +43 to +53; 17x9.5 front +37 to +59 / rear +37 to +59; 17x10 front +43 to +53 / rear +43 to +53 fit with modifications (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 2000-2003 Honda S2000. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

Modifications Required (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install)

FAQ

What is the bolt pattern of the 2000-2003 Honda S2000?

The 2000-2003 Honda S2000 (AP1) uses a 5X114.3 bolt pattern and a 64.1 mm center bore.

What size wheels came on the 2000-2003 Honda S2000 from the factory?

Factory sizes: 16x6.5 +55 front / 16x7.5 +65 rear; 17x7 +55 front / 17x8.5 +65 rear.

What lug thread size does the 2000-2003 Honda S2000 use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 2000-2003 Honda S2000 without modifications?

Bolt-on sizes run from 16" to 17" in diameter; see the size table for the offset range at each width.