Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mazda B-Series built from 1986 to 1993 (B2000, B2600, B2200, B2600i).
Every 1986-1993 Mazda B-Series uses a 6X139.7 bolt pattern with a 93.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 93.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mazda B-Series (UF) and the model years each was sold. All of them share the 6X139.7 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| B2000 | 1986-1987 | 14x5 +12 14x5.5 +15 15x6 +10 |
| B2600 | 1986-1987 | 15x6 +10 15x7 +10 |
| B2200 | 1988-1993 | 14x5 +12 14x5.5 +15 15x6 +10 |
| B2600i | 1988-1993 | See factory sizes below |
Wheel sizes Mazda fitted to the 1986-1993 Mazda B-Series from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 14x5 +12 |
| 14x5.5 +15 |
| 15x6 +10 |
| 15x6 +15 |
| 15x7 +10 |
| 16x7 +10 |
Widths and offsets with Verified Fitment on the 1986-1993 Mazda B-Series: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 14-18" | 5" | -9 to +22 |
| 14-18" | 5.5" | -2 to +20 |
| 14-18" | 6" | +4 to +14 |
Wider still: 14x7 -4 to +7; 15x7 -4 to +7; 16x7 -4 to +7; 17x7 -4 to +7; 18x7 -4 to +7 fit with modifications (trim front mud flaps / inner liner at full lock, roll fender lips, 1-2 in. lift (spacers) for larger all-terrain tires).
| Diameter | Width | Offset range |
|---|---|---|
| 15-18" | 6" | +4 to +14 |
Wider still: 15x7 -4 to +7; 16x7 -4 to +7; 17x7 -4 to +7; 18x7 -4 to +7 fit with modifications (trim front mud flaps / inner liner at full lock, roll fender lips, 1-2 in. lift (spacers) for larger all-terrain tires).
| Diameter | Width | Offset range |
|---|---|---|
| 14-18" | 5.5" | -2 to +20 |
| 14-18" | 6" | +4 to +14 |
Wider still: 14x7 -4 to +7; 15x7 -4 to +7; 16x7 -4 to +7; 17x7 -4 to +7; 18x7 -4 to +7 fit with modifications (trim front mud flaps / inner liner at full lock, roll fender lips, 1-2 in. lift (spacers) for larger all-terrain tires).
The 1986-1993 Mazda B-Series (UF) uses a 6X139.7 bolt pattern and a 93.1 mm center bore.
Factory sizes: 14x5 +12; 14x5.5 +15; 15x6 +10; 15x6 +15; 15x7 +10; 16x7 +10.
Its wheel fasteners use a M12x1.5 thread.
Bolt-on sizes run from 14" to 18" in diameter; see the size table for the offset range at each width.