Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mazda Mazda6 built from 2003 to 2008 (i, i Sport, i Touring, s, s Grand Touring, Mazdaspeed6).
Every 2003-2008 Mazda Mazda6 uses a 5X114.3 bolt pattern with a 67.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 67.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mazda Mazda6 (GG) and the model years each was sold. All of them share the 5X114.3 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| i | 2003-2008 | See factory sizes below |
| i Sport | 2006-2008 | 16x6.5 +55 |
| i Touring | 2006-2008 | See factory sizes below |
| s | 2003-2008 | See factory sizes below |
| s Grand Touring | 2006-2008 | See factory sizes below |
| Mazdaspeed6 | 2006-2007 | See factory sizes below |
Wheel sizes Mazda fitted to the 2003-2008 Mazda Mazda6 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 16x6.5 +55 |
| 16x7 +55 |
| 17x7 +60 |
| 17x7.5 +55 |
| 18x7 +55 |
| 18x7.5 +55 |
| 18x8 +55 |
Widths and offsets with Verified Fitment on the 2003-2008 Mazda Mazda6: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 16-20" | 7" | +38 to +60 |
| 16-20" | 7.5" | +44 to +54 |
Wider still: 16x8.5 +36 to +47; 17x8.5 +36 to +47; 18x8.5 +36 to +47; 19x8.5 +36 to +47; 20x8.5 +36 to +47 fit with modifications (roll front and rear fender lips, front camber bolts / rear camber adjustment for -1° or more, hub-centric rings if the wheel bore is larger).
| Diameter | Width | Offset range |
|---|---|---|
| 16-20" | 6.5" | +32 to +65 |
| 16-20" | 7" | +38 to +60 |
| 16-20" | 7.5" | +44 to +54 |
Wider still: 16x8.5 +36 to +47; 17x8.5 +36 to +47; 18x8.5 +36 to +47; 19x8.5 +36 to +47; 20x8.5 +36 to +47 fit with modifications (roll front and rear fender lips, front camber bolts / rear camber adjustment for -1° or more, hub-centric rings if the wheel bore is larger).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2003-2008 Mazda Mazda6. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.
Modifications Required (roll front and rear fender lips, front camber bolts / rear camber adjustment for -1° or more, hub-centric rings if the wheel bore is larger)









Modifications Required (roll front and rear fender lips, front camber bolts / rear camber adjustment for -1° or more, hub-centric rings if the wheel bore is larger)









The 2003-2008 Mazda Mazda6 (GG) uses a 5X114.3 bolt pattern and a 67.1 mm center bore.
Factory sizes: 16x6.5 +55; 16x7 +55; 17x7 +60; 17x7.5 +55; 18x7 +55; 18x7.5 +55; 18x8 +55.
Its wheel fasteners use a M12x1.5 thread.
Bolt-on sizes run from 16" to 20" in diameter; see the size table for the offset range at each width.