Mazda RX-7 (FC) 1986-1991 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mazda RX-7 built from 1986 to 1991 (GXL, Turbo II, Turbo, Convertible).

Fitment specs

Bolt pattern5X114.3
Center bore59.6 mm
Lug threadM12x1.5
Model years1986-1991
GenerationFC

Every 1986-1991 Mazda RX-7 uses a 5X114.3 bolt pattern with a 59.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 59.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Mazda RX-7 (FC) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
GXL1986-198915x6 +40
15x6.5 +40
Turbo II1987-1988See factory sizes below
Turbo1989-199116x6.5 +40
16x6.5 +40 front / 16x7.5 +40 rear
16x7 +40
16x7.5 +40
Convertible1988-199115x6 +40
15x6.5 +40

Factory wheel sizes

Wheel sizes Mazda fitted to the 1986-1991 Mazda RX-7 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
15x6 +40
15x6.5 +40
16x6.5 +40
16x6.5 +40 front / 16x7.5 +40 rear
16x7 +40
16x7.5 +40
17x7 +40
17x8 +40

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1986-1991 Mazda RX-7: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

GXL, Turbo II, Convertible

DiameterWidthFront offsetRear offset
15-17"6"+10 to +50+4 to +50
15-17"6.5"+17 to +56+10 to +56
15-17"7"+23 to +54+16 to +60
15-17"7.5"+29 to +48+23 to +54
15-17"8"+36 to +42+29 to +48
15-17"8.5"—+36 to +41

Wider still: 15x9.5 front — / rear +28 to +29; 16x9.5 front — / rear +28 to +29; 17x9.5 front — / rear +28 to +29 fit with modifications (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger).

Turbo

DiameterWidthFront offsetRear offset
16-17"6.5"+17 to +50+10 to +50
16-17"7"+23 to +54+16 to +56
16-17"7.5"+29 to +48+23 to +54
16-17"8"+36 to +42+29 to +48
16-17"8.5"—+36 to +41

Wider still: 16x9.5 front — / rear +28 to +29; 17x9.5 front — / rear +28 to +29 fit with modifications (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 1986-1991 Mazda RX-7. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

GXL, Turbo II, Convertible

Turbo

FAQ

What is the bolt pattern of the 1986-1991 Mazda RX-7?

The 1986-1991 Mazda RX-7 (FC) uses a 5X114.3 bolt pattern and a 59.6 mm center bore.

What size wheels came on the 1986-1991 Mazda RX-7 from the factory?

Factory sizes: 15x6 +40; 15x6.5 +40; 16x6.5 +40; 16x6.5 +40 front / 16x7.5 +40 rear; 16x7 +40; 16x7.5 +40; 17x7 +40; 17x8 +40.

What lug thread size does the 1986-1991 Mazda RX-7 use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 1986-1991 Mazda RX-7 without modifications?

Bolt-on sizes run from 15" to 17" in diameter; see the size table for the offset range at each width.