Mazda RX-7 (FD) 1993-1995 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mazda RX-7 built from 1993 to 1995 (Base, Touring, R1, R2, PEP).

Fitment specs

Bolt pattern5X114.3
Center bore67.1 mm
Lug threadM12x1.5
Model years1993-1995
GenerationFD

Every 1993-1995 Mazda RX-7 uses a 5X114.3 bolt pattern with a 67.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 67.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Mazda RX-7 (FD) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
Base1993-1995See factory sizes below
Touring1993-199516x8 +50
R1199316x8 +50
R2199416x8 +50
PEP1994-1995See factory sizes below

Factory wheel sizes

Wheel sizes Mazda fitted to the 1993-1995 Mazda RX-7 from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
16x8 +50
17x8 +50 front / 17x8.5 +50 rear
18x8 +45 front / 18x9 +45 rear

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1993-1995 Mazda RX-7: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

DiameterWidthOffset range
16-19"8"+33 to +55
16-19"8.5"+39 to +49

Wider still: 16x9.5 +31 to +42; 17x9.5 +31 to +42; 18x9.5 +31 to +42; 19x9.5 +31 to +42 fit with modifications (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 1993-1995 Mazda RX-7. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

Modifications Required (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger)

FAQ

What is the bolt pattern of the 1993-1995 Mazda RX-7?

The 1993-1995 Mazda RX-7 (FD) uses a 5X114.3 bolt pattern and a 67.1 mm center bore.

What size wheels came on the 1993-1995 Mazda RX-7 from the factory?

Factory sizes: 16x8 +50; 17x8 +50 front / 17x8.5 +50 rear; 18x8 +45 front / 18x9 +45 rear.

What lug thread size does the 1993-1995 Mazda RX-7 use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 1993-1995 Mazda RX-7 without modifications?

Bolt-on sizes run from 16" to 19" in diameter; see the size table for the offset range at each width.