Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mercedes-Benz E-Class Coupe built from 2010 to 2017 (E350, E400, E550).
Every 2010-2017 Mercedes-Benz E-Class Coupe uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M14x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz E-Class Coupe (C207) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| E350 | 2010-2015 | See factory sizes below |
| E400 | 2016-2017 | See factory sizes below |
| E550 | 2010-2017 | 17x7.5 +45 17x7.5 +45 front / 17x8.5 +49 rear 17x7.5 +45 front / 17x8.5 +40 rear 18x8 +45 18x8 +45 front / 18x8.5 +49 rear 18x8 +48 front / 18x8.5 +49 rear 19x8 +44 front / 19x8.5 +48 rear 19x8 +45 front / 19x9 +54 rear 19x8.5 +44 |
Wheel sizes Mercedes-Benz fitted to the 2010-2017 Mercedes-Benz E-Class Coupe from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 17x7.5 +45 |
| 17x7.5 +45 front / 17x8.5 +49 rear |
| 17x7.5 +45 front / 17x8.5 +40 rear |
| 18x8 +45 |
| 18x8 +45 front / 18x8.5 +49 rear |
| 18x8 +48 front / 18x8.5 +49 rear |
| 19x8 +44 front / 19x8.5 +48 rear |
| 19x8 +45 front / 19x9 +54 rear |
| 19x8.5 +44 |
Widths and offsets with Verified Fitment on the 2010-2017 Mercedes-Benz E-Class Coupe: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 17-20" | 7.5" | +28 to +50 | — |
| 17-20" | 8" | +34 to +44 | — |
| 17-20" | 8.5" | — | +32 to +54 |
| 17-20" | 9" | — | +38 to +48 |
Wider still: 17x10 front — / rear +30 to +41; 18x10 front — / rear +30 to +41; 19x10 front — / rear +30 to +41; 20x10 front — / rear +30 to +41 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 17-20" | 7.5" | +28 to +50 | +19 to +55 |
| 17-20" | 8" | +34 to +44 | +25 to +61 |
| 17-20" | 8.5" | — | +32 to +54 |
| 17-20" | 9" | — | +38 to +48 |
Wider still: 17x10 front — / rear +30 to +41; 18x10 front — / rear +30 to +41; 19x10 front — / rear +30 to +41; 20x10 front — / rear +30 to +41 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2010-2017 Mercedes-Benz E-Class Coupe. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.
Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)




















Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)












The 2010-2017 Mercedes-Benz E-Class Coupe (C207) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 17x7.5 +45; 17x7.5 +45 front / 17x8.5 +49 rear; 17x7.5 +45 front / 17x8.5 +40 rear; 18x8 +45; 18x8 +45 front / 18x8.5 +49 rear; 18x8 +48 front / 18x8.5 +49 rear; 19x8 +44 front / 19x8.5 +48 rear; 19x8 +45 front / 19x9 +54 rear; 19x8.5 +44.
Its wheel fasteners use a M14x1.5 thread.
Bolt-on sizes run from 17" to 20" in diameter; see the size table for the offset range at each width.