Bolt pattern, center bore, factory wheel sizes and the aftermarket widths and offsets that bolt on to the Mercedes-Benz GLE Coupe built from 2020 to 2026 (AMG GLE53 Coupe, AMG GLE63 S Coupe, GLE450 4MATIC Coupe).
Every 2020-2026 Mercedes-Benz GLE Coupe uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M15x1.25. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz GLE Coupe (C167) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years |
|---|---|
| AMG GLE53 Coupe | 2020-2026 |
| AMG GLE63 S Coupe | 2021-2026 |
| GLE450 4MATIC Coupe | 2024-2026 |
Wheel sizes Mercedes-Benz fitted to the 2020-2026 Mercedes-Benz GLE Coupe from the factory. Offsets are ET in millimeters.
| Factory size |
|---|
| 19x8.5 +42 |
| 19x8.5 +55 front / 19x8.5 +42 rear |
| 20x8.5 +42 |
| 20x8.5 +55 front / 20x8.5 +42 rear |
| 20x9 +44 |
| 20x9 +57 front / 20x9 +44 rear |
| 21x10 +54 front / 21x11 +49 rear |
| 21x11 +49 |
| 22x10 +56 front / 22x11 +50 rear |
| 22x11 +50 |
Widths and offsets with Verified Fitment on the 2020-2026 Mercedes-Benz GLE Coupe: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 19-22" | 8.5" | +18 to +65 | +21 to +52 |
| 23" | 8.5" | +18 to +65 | — |
| 19-22" | 9" | +24 to +71 | +27 to +49 |
| 23" | 9" | +24 to +71 | — |
| 19-22" | 9.5" | +30 to +66 | +33 to +43 |
| 23" | 9.5" | +30 to +66 | — |
| 19-23" | 10" | +37 to +59 | — |
| 19-23" | 10.5" | +43 to +53 | — |
Wider still: 19x11.5 front +35 to +46 / rear —; 20x11.5 front +35 to +46 / rear —; 21x11.5 front +35 to +46 / rear —; 22x11.5 front +35 to +46 / rear —; 23x11.5 front +35 to +46 / rear — fit with modifications (trim front wheel-well liner / bumper cover tabs, hub-centric rings (66.6 mm), check strut and spring clearance on the inner edge, longer ball-seat lug bolts with spacers).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2020-2026 Mercedes-Benz GLE Coupe. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.












Modifications Required (trim front wheel-well liner / bumper cover tabs, hub-centric rings (66.6 mm), check strut and spring clearance on the inner edge, longer ball-seat lug bolts with spacers)











The 2020-2026 Mercedes-Benz GLE Coupe (C167) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 19x8.5 +42; 19x8.5 +55 front / 19x8.5 +42 rear; 20x8.5 +42; 20x8.5 +55 front / 20x8.5 +42 rear; 20x9 +44; 20x9 +57 front / 20x9 +44 rear; 21x10 +54 front / 21x11 +49 rear; 21x11 +49; 22x10 +56 front / 22x11 +50 rear; 22x11 +50.
Its wheel fasteners use a M15x1.25 thread.
Bolt-on sizes run from 19" to 23" in diameter; see the size table for the offset range at each width.