Bolt pattern, center bore, factory wheel sizes and the aftermarket widths and offsets that bolt on to the Mercedes-Benz SLK built from 2012 to 2016 (SLK250, SLK300, SLK350, SLK55 AMG).
Every 2012-2016 Mercedes-Benz SLK uses a 5X112 bolt pattern with a 66.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 66.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mercedes-Benz SLK (R172) and the model years each was sold. All of them share the 5X112 bolt pattern.
| Submodel | Years |
|---|---|
| SLK250 | 2012-2015 |
| SLK300 | 2016 |
| SLK350 | 2012-2016 |
| SLK55 AMG | 2013-2016 |
Wheel sizes Mercedes-Benz fitted to the 2012-2016 Mercedes-Benz SLK from the factory. Offsets are ET in millimeters.
| Factory size |
|---|
| 16x7 +37.5 |
| 16x7 +38 front / 16x7.5 +45.5 rear |
| 16x7 +37.5 front / 16x8 +33.5 rear |
| 16x7 +38 front / 16x8 +45.5 rear |
| 16x7.5 +45.5 |
| 16x8 +33.5 |
| 17x7.5 +42 |
| 17x7.5 +42 front / 17x8.5 +36 rear |
| 17x8.5 +36 |
| 18x7.5 +42 |
| 18x7.5 +42 front / 18x8.5 +36 rear |
| 18x8.5 +36 |
| 18x9 +42 |
Widths and offsets with Verified Fitment on the 2012-2016 Mercedes-Benz SLK: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 16-18" | 7" | +18 to +47 | +4 to +47 |
| 16-18" | 7.5" | +25 to +47 | +10 to +54 |
| 16-18" | 8" | +31 to +41 | +16 to +51 |
| 16-18" | 8.5" | — | +23 to +45 |
| 16-18" | 9" | — | +29 to +38 |
Wider still: 16x9.5 front — / rear +15 to +38; 16x10 front — / rear +21 to +32; 17x9.5 front — / rear +15 to +38; 17x10 front — / rear +21 to +32; 18x9.5 front — / rear +15 to +38; 18x10 front — / rear +21 to +32 fit with modifications (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 2012-2016 Mercedes-Benz SLK. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.









Modifications Required (roll rear fender lips, adjustable camber parts for extra negative camber, hub-centric rings (66.6 mm), correct-length ball-seat lug bolts)







The 2012-2016 Mercedes-Benz SLK (R172) uses a 5X112 bolt pattern and a 66.6 mm center bore.
Factory sizes: 16x7 +37.5; 16x7 +38 front / 16x7.5 +45.5 rear; 16x7 +37.5 front / 16x8 +33.5 rear; 16x7 +38 front / 16x8 +45.5 rear; 16x7.5 +45.5; 16x8 +33.5; 17x7.5 +42; 17x7.5 +42 front / 17x8.5 +36 rear; 17x8.5 +36; 18x7.5 +42; 18x7.5 +42 front / 18x8.5 +36 rear; 18x8.5 +36; 18x9 +42.
Bolt-on sizes run from 16" to 18" in diameter; see the size table for the offset range at each width.