Bolt pattern, center bore, factory wheel sizes and the aftermarket widths and offsets that bolt on to the Mitsubishi Diamante built from 1992 to 1996 (Base, ES, LS).
Every 1992-1996 Mitsubishi Diamante uses a 5X114.3 bolt pattern with a 67.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 67.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Mitsubishi Diamante (1st Gen) and the model years each was sold. All of them share the 5X114.3 bolt pattern.
| Submodel | Years |
|---|---|
| Base | 1992-1996 |
| ES | 1992-1996 |
| LS | 1992-1996 |
Wheel sizes Mitsubishi fitted to the 1992-1996 Mitsubishi Diamante from the factory. Offsets are ET in millimeters.
| Factory size |
|---|
| 14x5.5 +46 |
| 15x5.5 +46 |
| 15x6 +46 |
| 15x6.5 +46 |
| 15x6.5 +48 |
| 16x6 +46 |
| 16x6.5 +48 |
| 16x7 +46 |
| 17x6.5 +48 |
| 17x7 +44 |
| 17x7 +46 |
| 17x7.5 +44 |
| 18x7 +44 |
| 18x7.5 +44 |
Widths and offsets with Verified Fitment on the 1992-1996 Mitsubishi Diamante: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 14-18" | 6" | +29 to +51 |
| 14-18" | 6.5" | +35 to +45 |
Wider still: 14x7.5 +27 to +38; 15x7.5 +27 to +38; 16x7.5 +27 to +38; 17x7.5 +27 to +38; 18x7.5 +27 to +38 fit with modifications (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 1992-1996 Mitsubishi Diamante. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.
Modifications Required (roll front and rear fender lips, front camber bolts for -1°, hub-centric rings if the wheel bore is larger)
The 1992-1996 Mitsubishi Diamante (1st Gen) uses a 5X114.3 bolt pattern and a 67.1 mm center bore.
Factory sizes: 14x5.5 +46; 15x5.5 +46; 15x6 +46; 15x6.5 +46; 15x6.5 +48; 16x6 +46; 16x6.5 +48; 16x7 +46; 17x6.5 +48; 17x7 +44; 17x7 +46; 17x7.5 +44; 18x7 +44; 18x7.5 +44.
Its wheel fasteners use a M12x1.5 thread.
Bolt-on sizes run from 14" to 18" in diameter; see the size table for the offset range at each width.