Mitsubishi Diamante 2nd Gen 1997-2004 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Mitsubishi Diamante built from 1997 to 2004 (ES, LS, VR-X).

Fitment specs

Bolt pattern5X114.3
Center bore67.1 mm
Lug threadM12x1.5
Model years1997-2004
Generation2nd Gen

Every 1997-2004 Mitsubishi Diamante uses a 5X114.3 bolt pattern with a 67.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 67.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Mitsubishi Diamante (2nd Gen) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
ES1997-200415x6 +46
16x6 +46
LS1997-200416x6 +46
VR-X1997-200416x6 +46

Factory wheel sizes

Wheel sizes Mitsubishi fitted to the 1997-2004 Mitsubishi Diamante from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
15x6 +46
16x6 +46
17x6.5 +48
17x7 +44
17x7 +46
18x7 +44
18x7.5 +44

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1997-2004 Mitsubishi Diamante: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

ES

DiameterWidthOffset range
15-17"6"+22 to +56
15-17"6.5"+29 to +51
15-17"7"+35 to +45

Wider still: 15x8 +27 to +38; 16x8 +27 to +38; 17x8 +27 to +38 fit with modifications (roll front and rear fender lips, front camber bolts / rear camber adjustment for -1° or more, hub-centric rings if the wheel bore is larger).

LS, VR-X

DiameterWidthOffset range
16-17"6"+22 to +56
16-17"6.5"+29 to +51
16-17"7"+35 to +45

Wider still: 16x8 +27 to +38; 17x8 +27 to +38 fit with modifications (roll front and rear fender lips, front camber bolts / rear camber adjustment for -1° or more, hub-centric rings if the wheel bore is larger).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 1997-2004 Mitsubishi Diamante. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

ES

Modifications Required (roll front and rear fender lips, front camber bolts / rear camber adjustment for -1° or more, hub-centric rings if the wheel bore is larger)

LS, VR-X

Modifications Required (roll front and rear fender lips, front camber bolts / rear camber adjustment for -1° or more, hub-centric rings if the wheel bore is larger)

FAQ

What is the bolt pattern of the 1997-2004 Mitsubishi Diamante?

The 1997-2004 Mitsubishi Diamante (2nd Gen) uses a 5X114.3 bolt pattern and a 67.1 mm center bore.

What size wheels came on the 1997-2004 Mitsubishi Diamante from the factory?

Factory sizes: 15x6 +46; 16x6 +46; 17x6.5 +48; 17x7 +44; 17x7 +46; 18x7 +44; 18x7.5 +44.

What lug thread size does the 1997-2004 Mitsubishi Diamante use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 1997-2004 Mitsubishi Diamante without modifications?

Bolt-on sizes run from 15" to 17" in diameter; see the size table for the offset range at each width.