Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Porsche 911 Targa built from 2013 to 2016 (Carrera 4, Carrera 4S, Targa 4, Targa 4S).
Every 2013-2016 Porsche 911 Targa uses a 5X130 bolt pattern with a 71.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 71.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Porsche 911 Targa (991) and the model years each was sold. All of them share the 5X130 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| Carrera 4 | 2013-2016 | See factory sizes below |
| Carrera 4S | 2013-2016 | 19x11 +48 20x11 +52 20x11.5 +48 |
| Targa 4 | 2014-2016 | See factory sizes below |
| Targa 4S | 2014-2016 | 19x11 +48 20x11 +52 20x11.5 +48 |
Wheel sizes Porsche fitted to the 2013-2016 Porsche 911 Targa from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 19x11 +48 |
| 19x11 +56 |
| 19x11.5 +56 |
| 20x11 +52 |
| 20x11 +56 |
| 20x11.5 +48 |
| 20x11.5 +56 |
| 20x12 +50 |
| 20x12 +63 |
Widths and offsets with Verified Fitment on the 2013-2016 Porsche 911 Targa: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 19-21" | 11" | +31 to +58 |
| 19-21" | 11.5" | +37 to +64 |
| 19-21" | 12" | +44 to +68 |
| 19-21" | 12.5" | +50 to +62 |
| 19-21" | 13" | +56 |
Wider still: 19x13.5 +42 to +55; 19x14 +48 to +49; 20x13.5 +42 to +55; 20x14 +48 to +49; 21x13.5 +42 to +55; 21x14 +48 to +49 fit with modifications (roll rear fender lips, rear camber/toe adjustment for extra negative camber, hub-centric rings (71.6 mm) if wheel bore is larger, longer wheel bolts when running spacers).
The 2013-2016 Porsche 911 Targa (991) uses a 5X130 bolt pattern and a 71.6 mm center bore.
Factory sizes: 19x11 +48; 19x11 +56; 19x11.5 +56; 20x11 +52; 20x11 +56; 20x11.5 +48; 20x11.5 +56; 20x12 +50; 20x12 +63.
Bolt-on sizes run from 19" to 21" in diameter; see the size table for the offset range at each width.