Toyota Venza (AV10) 2009-2015 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Toyota Venza built from 2009 to 2015 (Base, LE, XLE, Limited).

Fitment specs

Bolt pattern5X114.3
Center bore60.1 mm
Lug threadM12x1.5
Model years2009-2015
GenerationAV10

Every 2009-2015 Toyota Venza uses a 5X114.3 bolt pattern with a 60.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 60.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the Toyota Venza (AV10) and the model years each was sold. All of them share the 5X114.3 bolt pattern.

SubmodelYearsFactory wheel sizes
Base2009-2012See factory sizes below
LE2013-201519x7.5 +35
XLE2013-201519x7.5 +35
Limited2013-201520x7.5 +35

Factory wheel sizes

Wheel sizes Toyota fitted to the 2009-2015 Toyota Venza from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
19x7.5 +35
20x7.5 +35

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 2009-2015 Toyota Venza: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

Base, LE, XLE

DiameterWidthOffset range
19-22"7.5"+18 to +40
19-22"8"+24 to +34

Wider still: 19x9 +16 to +27; 20x9 +16 to +27; 21x9 +16 to +27; 22x9 +16 to +27 fit with modifications (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels).

Limited

DiameterWidthOffset range
20-22"7.5"+18 to +40
20-22"8"+24 to +34

Wider still: 20x9 +16 to +27; 21x9 +16 to +27; 22x9 +16 to +27 fit with modifications (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels).

Wheels in stock that fit

In-stock PG WHEELS sets in sizes with Verified Fitment for the 2009-2015 Toyota Venza. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.

Base, LE, XLE

Modifications Required (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels)

Limited

Modifications Required (trim front bumper cover / fender liner at full lock, roll rear fender lips, hub-centric rings for aftermarket wheels)

FAQ

What is the bolt pattern of the 2009-2015 Toyota Venza?

The 2009-2015 Toyota Venza (AV10) uses a 5X114.3 bolt pattern and a 60.1 mm center bore.

What size wheels came on the 2009-2015 Toyota Venza from the factory?

Factory sizes: 19x7.5 +35; 20x7.5 +35.

What lug thread size does the 2009-2015 Toyota Venza use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 2009-2015 Toyota Venza without modifications?

Bolt-on sizes run from 19" to 22" in diameter; see the size table for the offset range at each width.