BMW 3 Series (E30) 1984-1991 Wheel Fitment Guide

Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the BMW 3 Series built from 1984 to 1991 (318i, 318i, 318is, 325e, 325es, 325i, 325is, 325iX).

Fitment specs

Bolt pattern4X100
Center bore57.1 mm
Lug threadM12x1.5
Model years1984-1991
GenerationE30

Every 1984-1991 BMW 3 Series uses a 4X100 bolt pattern with a 57.1 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 57.1 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.

Years & submodels

US-market submodels of the BMW 3 Series (E30) and the model years each was sold. All of them share the 4X100 bolt pattern.

SubmodelYearsFactory wheel sizes
318i1984-198514x5.5 +35
14x6 +35
14x6.5 +30
15x7 +24
318i199114x5.5 +35
14x6 +35
14x6.5 +30
15x7 +24
318is199114x5.5 +35
14x6 +35
14x6.5 +30
15x7 +24
325e1984-198814x5.5 +35
14x6 +35
14x6.5 +30
15x7 +24
325es1986-198814x5.5 +35
14x6 +35
14x6.5 +30
15x7 +24
325i1987-199114x5.5 +35
14x6 +35
14x6.5 +30
15x7 +24
325is1987-199114x5.5 +35
14x6 +35
14x6.5 +30
15x7 +24
325iX1988-199114x5.5 +35
14x6 +35
14x6.5 +45
15x7 +41

Factory wheel sizes

Wheel sizes BMW fitted to the 1984-1991 BMW 3 Series from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.

Factory size
13x5.5 +35
14x5.5 +35
14x6 +35
14x6.5 +30
14x6.5 +45
15x7 +24
15x7 +41

Aftermarket sizes that bolt on

Widths and offsets with Verified Fitment on the 1984-1991 BMW 3 Series: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.

DiameterWidthOffset range
14-16"5.5"+5 to +45
14-16"6"+11 to +51
14-16"6.5"+18 to +53
14-16"7"+24 to +46
14-16"7.5"+30 to +40

Wider still: 14x8.5 +22 to +33; 15x8.5 +22 to +33; 16x8.5 +22 to +33 fit with modifications (roll front and rear fender lips, front camber plates for low offsets, hub-centric rings if wheel bore is larger than the hub).

FAQ

What is the bolt pattern of the 1984-1991 BMW 3 Series?

The 1984-1991 BMW 3 Series (E30) uses a 4X100 bolt pattern and a 57.1 mm center bore.

What size wheels came on the 1984-1991 BMW 3 Series from the factory?

Factory sizes: 13x5.5 +35; 14x5.5 +35; 14x6 +35; 14x6.5 +30; 14x6.5 +45; 15x7 +24; 15x7 +41.

What lug thread size does the 1984-1991 BMW 3 Series use?

Its wheel fasteners use a M12x1.5 thread.

What aftermarket wheel sizes fit the 1984-1991 BMW 3 Series without modifications?

Bolt-on sizes run from 14" to 16" in diameter; see the size table for the offset range at each width.