Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the BMW 3 Series built from 1999 to 2005 (323i, 323Ci, 325i, 325xi, 325Ci, 325ti, 328i, 328Ci, 330i, 330xi, 330Ci).
Every 1999-2005 BMW 3 Series uses a 5X120 bolt pattern with a 72.6 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 72.6 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the BMW 3 Series (E46) and the model years each was sold. All of them share the 5X120 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| 323i | 1999-2000 | See factory sizes below |
| 323Ci | 1999-2000 | See factory sizes below |
| 325i | 2001-2005 | 16x7 +34 17x8 +34 17x8 +34 front / 17x8.5 +37 rear 18x8 +34 front / 18x8.5 +37 rear |
| 325xi | 2001-2005 | 16x7 +34 17x8 +34 17x8.5 +37 18x8.5 +37 |
| 325Ci | 2001-2005 | See factory sizes below |
| 325ti | 2001-2005 | See factory sizes below |
| 328i | 1999-2000 | See factory sizes below |
| 328Ci | 1999-2000 | See factory sizes below |
| 330i | 2001-2005 | 17x8 +34 17x8.5 +37 18x8.5 +37 |
| 330xi | 2001-2005 | 17x8 +34 17x8.5 +37 18x8.5 +37 |
| 330Ci | 2001-2005 | See factory sizes below |
Wheel sizes BMW fitted to the 1999-2005 BMW 3 Series from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 15x6.5 +42 |
| 16x7 +46 |
| 17x7 +47 |
| 17x7.5 +41 front / 17x8.5 +50 rear |
| 17x8 +47 |
| 17x8.5 +50 |
| 18x8 +47 front / 18x8.5 +50 rear |
| 18x8.5 +50 |
Widths and offsets with Verified Fitment on the 1999-2005 BMW 3 Series: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Offset range |
|---|---|---|
| 15-19" | 6.5" | +11 to +52 |
| 15-19" | 7" | +17 to +58 |
| 15-19" | 7.5" | +24 to +59 |
| 15-19" | 8" | +30 to +52 |
| 15-19" | 8.5" | +36 to +46 |
Wider still: 15x9.5 +28 to +39; 16x9.5 +28 to +39; 17x9.5 +28 to +39; 18x9.5 +28 to +39; 19x9.5 +28 to +39 fit with modifications (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install).
| Diameter | Width | Offset range |
|---|---|---|
| 16-19" | 7" | +17 to +44 |
| 16-19" | 7.5" | +24 to +50 |
| 16-19" | 8" | +30 to +52 |
| 16-19" | 8.5" | +36 to +46 |
Wider still: 16x9.5 +28 to +39; 17x9.5 +28 to +39; 18x9.5 +28 to +39; 19x9.5 +28 to +39 fit with modifications (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install).
| Diameter | Width | Offset range |
|---|---|---|
| 17-19" | 8" | +30 to +44 |
| 17-19" | 8.5" | +36 to +46 |
Wider still: 17x9.5 +28 to +39; 18x9.5 +28 to +39; 19x9.5 +28 to +39 fit with modifications (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 1999-2005 BMW 3 Series. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.





Modifications Required (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install)

















Modifications Required (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install)
















Modifications Required (roll the fender lips, add negative camber (camber bolts or arms), wheel alignment after install)












The 1999-2005 BMW 3 Series (E46) uses a 5X120 bolt pattern and a 72.6 mm center bore.
Factory sizes: 15x6.5 +42; 16x7 +46; 17x7 +47; 17x7.5 +41 front / 17x8.5 +50 rear; 17x8 +47; 17x8.5 +50; 18x8 +47 front / 18x8.5 +50 rear; 18x8.5 +50.
Its wheel fasteners use a M12x1.5 thread.
Bolt-on sizes run from 15" to 19" in diameter; see the size table for the offset range at each width.