Bolt pattern, center bore, factory wheel sizes for each submodel and the aftermarket widths and offsets that bolt on to the Chevrolet Corvette built from 1997 to 2004 (Base, Z06).
Every 1997-2004 Chevrolet Corvette uses a 5X120.65 / 5X120 bolt pattern with a 70.3 mm hub (center bore). Most aftermarket wheels are machined with a larger bore so one wheel can fit many cars; fit hub-centric rings with a 70.3 mm inner diameter so the wheel centers on the hub instead of the lugs. Lug thread is M12x1.5. Torque the lugs to the figure in your owner's manual and re-check them after the first 50 miles.
US-market submodels of the Chevrolet Corvette (C5) and the model years each was sold. All of them share the 5X120.65 / 5X120 bolt pattern.
| Submodel | Years | Factory wheel sizes |
|---|---|---|
| Base | 1997-2004 | See factory sizes below |
| Z06 | 2001-2004 | 17x9.5 +54 front / 18x10.5 +58 rear |
Wheel sizes Chevrolet fitted to the 1997-2004 Chevrolet Corvette from the factory (all submodels; the table above lists them by submodel). Offsets are ET in millimeters.
| Factory size |
|---|
| 17x8.5 +58 front / 18x9.5 +65 rear |
| 17x9.5 +54 front / 18x10.5 +58 rear |
Widths and offsets with Verified Fitment on the 1997-2004 Chevrolet Corvette: no fender rolling, spacers or camber changes, and the wheel sits like the factory one or a little further out. Offsets outside a range below either rub, poke past the fender or sit tucked in. Test-fit one wheel for brake and suspension clearance before mounting tires.
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 17-19" | 8.5" | +35 to +63 | — |
| 17-19" | 9" | +42 to +57 | — |
| 17-19" | 9.5" | +48 to +51 | +39 to +70 |
| 17-19" | 10" | — | +45 to +64 |
| 17-19" | 10.5" | — | +52 to +58 |
Wider still: 17x11 front — / rear +46 to +57; 18x11 front — / rear +46 to +57; 19x11 front — / rear +46 to +57 fit with modifications (roll front and rear fender lips, camber adjustment (shims / eccentric bolts) for wider rears, extended wheel studs if spacers are used).
| Diameter | Width | Front offset | Rear offset |
|---|---|---|---|
| 17-19" | 9.5" | +48 to +53 | — |
| 18-19" | 10.5" | — | +52 to +58 |
Wider still: 18x11 front — / rear +46 to +57; 19x11 front — / rear +46 to +57 fit with modifications (roll front and rear fender lips, camber adjustment (shims / eccentric bolts) for wider rears, extended wheel studs if spacers are used).
In-stock PG WHEELS sets in sizes with Verified Fitment for the 1997-2004 Chevrolet Corvette. Each card shows only the sizes that fit; prices are for a set of 4 with free shipping in the lower 48.
Modifications Required (roll front and rear fender lips, camber adjustment (shims / eccentric bolts) for wider rears, extended wheel studs if spacers are used)












Modifications Required (roll front and rear fender lips, camber adjustment (shims / eccentric bolts) for wider rears, extended wheel studs if spacers are used)












The 1997-2004 Chevrolet Corvette (C5) uses a 5X120.65 / 5X120 bolt pattern and a 70.3 mm center bore.
Factory sizes: 17x8.5 +58 front / 18x9.5 +65 rear; 17x9.5 +54 front / 18x10.5 +58 rear.
Its wheel fasteners use a M12x1.5 thread.
Bolt-on sizes run from 17" to 19" in diameter; see the size table for the offset range at each width.